anycubic 4max pro extruder 3d models

Designed for swiftly relocating the current reel mount location above the printer.\r\n\r\nCrafted in a two-part design to accommodate the 4Max Pro bed and ensure seamless assembly via screws, bolts, adhesive, welding, or roll...

Child Safety for the 4max Pro On/Off Switch. The printer can only be turned on and off using an object with a diameter of less than 4mm now. To assemble, you can use hot glue. I used it and slightly damaged the coating of the housing. With a little...

BLTouch sensor holder for Anycubic 4max with MK8 extruder integration, along with a hotend fan holder measuring 40x40x10mm in size. Note that this design won't be compatible with the original 40x40x20mm super loud fan. The X offset is set at 37mm, Y...

I was attempting to create a dual fan full circular part cooling fan duct but it failed miserably due to inadequate space around the extruder on my Anycubic 4Max. Ultimately, I ended up with this design and I'm unsure if it surpasses the...

Thanks Print Settings Printer Brand: Anycubic Printer: Semi-closed 4Max Rafts: No Supports: No Resolution: .2 Infill: 20% Notes: Print with 3 shells and 12 top, 12 bottom layers for extra strength. How I Designed This All parts were designed in...

Human Pro 4000 Tray System

* English * Dual Spool Holder for Anycubic 4Max Required: 10 x 3.16 mm screws, 3 x M4 nuts, 3 x 0.39 inch screws, 2 x 0.79 inch screws, 2 x 0.079 inch T-nuts (2020) Internal spool diameter: 1.77 inches

Fan duct for Anycubic 4MAX. ... Print parameters in Cura: Layer Height 0.3mm Line width 0.5mm Shell: Wall Line Count - 2 Support: Generate support - checked Support: Support Placement - Touching Buildplate Support: Support Density 40% Experimental:...

A straightforward solution for the Anycubic 4MAX. A simple spool holder is all that's required, utilizing a spool that moves the filament roll forward to provide full clearance on the rear side. The tube is hollow and tapers inwards, eliminating the...

-------------------------- This is a new version of the duck cooler with three white LEDs specifically designed for Anycubic 4MAX printers. ATTENTION: I assume no responsibility whatsoever for poorly wired connections, malfunctions, or even damage...

I created this one specifically for my Anycubic 4Max; for more information check out the original link above. UPDATE: I had to update the design, as the O-Ring was limiting wheel travel; the updated version is now v2, with more details about the...

Cooling Duct for Anycubic 4Max. This duct is specifically designed to work with a 50x50x25 blower fan. A new version of this design can be found that is tailored to the original 5015 blower fan at https://www.thingiverse.com/thing:2895611. Since...

For more details, please see the description below: Summary Cooling Duct for Anycubic 4Max. This duct is designed specifically for a 50x50x25 blower fan. Since there's no room for screws, I created two holes to use a ribbon to keep the fan securely...

This is a enclosement for the top of the Anycubic 4max. So you should have a good base to print ABS. This Version has three Windows, one in the front one on the left sideand one on the top cover. The right side is open for the moving cables. Thinking...

This enclosure tops the Anycubic 4max, providing a solid base for printing ABS. Three windows adorn this version - one on the front, one on the left side, and one on the top cover. The right side remains open for cable management, with plans to close...

Easier Closure for the Floor Plate in the 4Max to Prevent Pressed Air from Always Leaking Out Below and Drawing Cold Air Downward from Below.

Initially written for my Tevo Tornado but adjusted for the Anycubic 4MAX, this Gcode is likely also suitable for the Ender 3 and clones without touchscreen. Just check the short and simple Gcode. The Gcode files contain two patterns for leveling:...

I'd love to collaborate on enhancing the 4Max 3D printer's accessory designs, and I'm confident that our combined efforts will lead to some truly innovative solutions!

This is an extruder fan remix for my Anycubic 4 Max which has loose spacers between the extruder and the fan that always end up falling out and rolling out of sight or being a fiddle to hold and line up when refitting if i had to remove the fan to...

This cover is designed to fit snugly over the bottom hole in your 4MAX printer. To store scraps from the heatbed, I've utilized a space under my bed - however, I'm not satisfied with how frequently they fall out. This modification should address that...

i like the original idea for the makerbot Replicator 2 series by UoBQuantumMatter nice work, but do not fit at all on my 4MAX so i re did the model from scratch using FreeCad. For installation i use the same screw that hold the front panel, enjoy it...

Humans are now able to purchase an upper enclosure kit designed specifically for the Anycubic Forma 3D printer.

However, I have to admit that it just didn't work out for my 4MAX printer at all, so I decided to start from scratch using FreeCad to create my own model. To assemble it, I simply used the same screws that hold the front panel in place, and now my...

I'm working on enclosing my 4Max completely, so I created these three covers for holes in the box. The Bottom Hole Cover isn't pictured, but it's designed for the big slot at the bottom just inside the door. My inspiration came from Logodruck's...

... we must prioritize fire protection. You won't receive compensation from AnyCubic if your home burns down! I hope this drawing proves useful to you! Remember: 3D printers are a significant fire hazard! ...Take proactive measures to mitigate it...

It mounts to the extruder fan screws I also added some spacers for the original 20mm fan and for a 10mm fan. Inserting the dial indicator can be a bit tight depends on how well your printer is leveled and how much support you use inside the...

This is a mount for a TEVO Titan extruder. Primary objective was to utilize stock components without sacrificing any print space (X-Y). I employed a V6 heatsink and heatbreak paired with the stock heatblock and a V6 nozzle. Parts can be printed...

This is a remix for Anycubic 4Max Pro - adjusted height because on my printer it did not fit well - increased size of the vents for better airflow - added another screw mount point for better stability

Holding a precision dial indicator with a 3/8" or 9.5mm shaft on the extruder head streamlines bed leveling for the Anycubic 4Max Pro. A spare threaded insert, compatible with an M3x6 bolt, is conveniently located on the left-hand side of the head to...

A miniature of the Anycubic 4Max Pro as a Filament Cleaner Print Settings Printer: 4Max Pro Rafts: NoSupports: No Resolution: 0.1Infill: 100 Category: 3D Printer Accessories