any cubic mono x 3d models

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

<p>Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP.</p> <p>Instructions:</p> <ol> <li>Remove the bed plate.</li> <li>Take an old...

This remix include: -prolonging the hanger to better support printing bed - it should stop rotating around the screw - it was 2 mm short in my printer -adding cut off so the screw lay flat on bed (earlier it was partially on hanger partially on...

this is a remix of another design rotated 180 degree and made to sit on the right side. angled to drip into resin vat. ... resized for a easier fit.

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Remix of https://www.thingiverse.com/thing:4640934 MonoX build plate model by mrfumetsu. Adjusted the size of the build plate to 202x128mm. In the original model the build plate was 220mm wide (typo when designing?). ... The other parts -...

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

Just a quick file to clean out your vat without having to dump all of the resin out. This is good for small failures where you might have something stuck to your FEP. Instructions: 1. Remove the bed plate. 2. Take an old support piece with a flat...

Customized version of https://www.thingiverse.com/thing:4974330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4974330

(In combination with my design: I've tested 5 dripping holders, this was the best option so far read how to use it best. https://www.thingiverse.com/thing:4765628) A simple but effective way to prevent those few drops from reaching just outside the...

Hello there, this is a support to let you to drain your resin bottle in to the VAT. It could be used with plate installed or not, and also with different size of resin. I think is very useful and in different situations. ...

this is tight, you will need a hair dryer to heat up the plastic (pla) then slide it on all the way back, it was also designed to fit snug with the build plate so it doesn't shift when screwing it down after each print.

The new axis is fully compatible with the original Anycubic 50mm X-gantry system and can be used in any Anycubic I3M configuration, including original or customized X carriages, cable chains, extruders fixed to the Z axis (original design), on top...

MODEL MADE FOR RESIN PRINTING WITH PHOTON MONO X AND ELEGOO SATURN DIVIDED INTO 2 PARTS INCLUDING SLICING FILES CREATED WITH LYCHEE INCLUDES BASE VBUCK

So now its only the base. Please use the following instead: ANYCUBIC Photon Mono X Clip On Heater Mount https://www.thingiverse.com/thing:5190198 Here are my other designs for the Anycubic Mono X 4K ANYCUBIC Photon Mono X Z-Axis Bumper Guard...

I'm giving the initial test to my freshly installed motherboard using the Ubuntu Linux system. ...I encountered an issue with Blender where it struggled to render 1,000 frames at a resolution of 512x512 pixels.

No description provided.

Great Cube! ...:)

Cube is designed on ,,Autodesk Inventor“. 3D puzzle has 11 different pieces. ...It’s a great challenge for puzzle lovers.

Gyroid Cubic

Cubic Dice

Cubic Dice

Build plate hang and drip bracket for Anycubic Photon Mono X. ...Allows you to hang the build plate at an angle and remove the parts as the excess resin drips back into the vat.

I made this replacement when my Z leveller on my Anycubic Photon Mono X broke - There is a Z offset spacer as well in case you need it to add height when installing a magnetic plate for your print bed or if you have a Z offset problem on your printer...