anti z 3d models

Print two times, one of which must be with a reflective surface.

This remix is based on the original design found at https://www.thingiverse.com/thing:2599816. ...I created this alternative to utilize an 8mm iron rod, or even an 8mm aluminum rod if you prefer, instead of the original 6mm carbon rod used in the file.

Improvement of https://www.thingiverse.com/thing:808509 is now available for Prusa i3 users who are struggling with the same issue. ...After implementing this upgrade, my printing problems were instantly resolved.

Use this roller bearing with a diameter of 625 units. ...For printers that utilize a rod or spindle with a diameter of five millimeters.

In addition to these two models:http://www.thingiverse.com/thing:1103976http://www.thingiverse.com/thing:2067676 I've modified the design to eliminate the hole for nuts, making it easier to assemble and use. ...The updated model is also slightly...

I remixed the work done by nanodesigner since I did not have n52 magnets but only n32. I make the holes for magnets a bit deeper to install 2 n32 magnets per hole, I think that made the magnets strong enough to get good results. This means you...

People using M5 threaded rods will find this helpful.

I redesigned the model under ANET size and printed it successfully. However, the first iteration was a poor replica due to issues with cap screws and an overall lack of stability resulting from the minimal contact area between components. The final...

I rebuilt the model using Anet dimensions and printed it. Unfortunately, the result was subpar due to issues with cap screws and reduced stability caused by a small contact area. However, subsequent refinements resolved these problems effectively. ...To...

I've adjusted the Tronxy P802MA printer's column spacing to bring the holes closer together, allowing for a better fit. This modification is designed to work seamlessly with standard 608 bearings. ...Note: As a beginner in this field, if you encounter...

As time went by, I found myself repeatedly tightening and loosening the screws, which eventually led to a problem - the tab that they passed through began to develop cracks or even break apart entirely. ...To prevent this from happening, I reinforced...

Replacement legs for my Vizio E50-E3. I do not have original part, so I made it using caliper and photos from internet. vizio_e50_left_leg.stl and vizio_e50_right_leg.stl - full size models vizio_e50_left_leg1.stl +vizio_e50_left_leg2.stl =...

Remove defect from flawed prints.

I adjusted the centers to 25mm and reduced the bearing outer diameter slightly, ensuring a precise fit in my case. This modification is specifically designed for M3 screws. ...If you're interested in the original file, it can be accessed at...

Another way to compensate wobble is by separating the parts in the file and printing them in ABS or nylon. After they are printed, polish each part with a triangle rasp because the parts should slide easily. The outer ring, featuring a larger middle...

Create a variant after printing.

The original was pretty good like it was. I just made some little upgrades. - I use ball bearings from skateboards (https://www.amazon.de/gp/product/B076KM4QLC/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1) and had to make the hole a bit bigger.

Modified Simple Anti Z Wobble for Anet A8 by robertlox, for long Z axis Remix from https://www.thingiverse.com/thing:2121017

Anti Z Wobble lead screw and Anti Backlash. It perfectly fits the TR 8x1.5 Trapezoid Rod. Designed for 8mm rods, this reliable solution ensures smooth operation. ...Hex Nut version available at https://www.thingiverse.com/thing:2444330

Original Hesine M505 - Anet A8 Upgrade Kit (Updated): http://www.thingiverse.com/thing:1718315 Anti Z wobble I used (Anti Z Wobble for Anet A8 (using 16x8x5 bearing)): http://www.thingiverse.com/thing:1890670 This is version two of my IGUS x-mounts....

I no longer have the XYZ Printing Da Vinci 1.0A printer, so I'd like to share my design of an anti-Z-wobble bracket. Unfortunately, I didn't get a chance to fully test it. The idea behind this design is that the wobble of the Z-axis can be...

Simple anti z-wobble device for Ender 3 / 3 Pro / 3 V2 Simply device for reducing z-wobble caused of low quality lead screw. This is remix of https://www.thingiverse.com/thing:4387638. Use 10 small neodymium magnets (8x3mm) and balls from baering...

As I no longer have XYZ Printing Da Vinci 1.0A printer, I'd like to share my design of anti Z-wobble bracket. I didn't have a chance to test it fully. The idea is that the wobble of Z axis are compensated by the springy spiral arms of the bracket and...

This is another Anti-Z-Wobble accessory. I wasn't satisfied with the designs I found on Thingiverse. I tried two of them, and it was necessary to post-process them with sandpaper or a file. That's why I made one myself. This is for the M8-brass nut...

This anti-z-wobble bed mount in BLV-Cube printer with two SFU1204 ball screws and motor mount + lower bearing block BK10. Motor mount and BK10 is a gentle remix from https://www.thingiverse.com/Cpt_Obvious (greetings!) from project:...

I reinforced the original Anti Wobble for the Z Axis by installing M3 screw anchors, which provide a much stronger hold due to their presence of pre-drilled holes.

I designed a plug-and-play Z axis anti-wobble system that works with most 3D printers using 8mm rods and NEMA 17 stepper motors (approximately 40x40mm). ...I prefer it to a top cap holder because if the Z rods are not perfectly straight, it doesn't...

Video inspired by thingiverse.com/thing84640 wobbless X mounts odudex Modified by sigma3D to fix unstraight threaded rod Z elevator wobble problem found at thingiverse.com/thing817504 Anti Wobble Print Settings: Printer: Sigma3D Rafts: No Supports:...

-Plug&play Z axis anti wobble system that is suitable for most of 3d printers with 8mm rods and nema 17 stepper -Hardware needed: 1 x 688RS bearing for each stepper motor (688 RS 8x16x5mm) 2 x M3x16mm bolts for each stepper motor 2 x m4x16mm 2...

Instructions You will need: -2 x M6 screws (the shorter, the better - aim for 6-10mm length) -4 x M4 screws (16mm length is recommended) -4 x M4 nuts -2 x Anti-Backlash Nuts from DumpsterCNC (make sure to select "add flange option" #2, refer to my...