antec hard drive tray 3d models

Antec P180/P182 hard drive tray for the top drive cage. An extra pair of holes is added to the original tray so it can fit new drives that don't have the middle screw holes. 2 designs are provided. One for the original Antec screws and grommets,...

For more information on installing large hard drives in the Antec P280 case, refer to these online resources: 1) https://linustechtips.com/main/topic/834834-antec-p280-drive-tray-does-not-support-810-tb-hard-disks/ 2)...

I modified the Antec hard drive enclosure using it as a starting point and reimagined it for 3D printing. ...By removing the clip, I was able to overcome its limitations with PLA filament and create a secure, snug-fitting design that effectively holds...

A user was seeking straightforward drive mounting solutions for an ANTEC P180 enclosure.

Antec P180/P182 lower drive cage for 4 HDDs. Items to print: 1x Top panel (with support) 1x Bottom panel (with support) 2x Side panels (with support) 2x Center slides (no support) Optional: 4x Long alignment pins to attach center slide to...

After scaling to compensate didn't help and not caring about it being tool less, I just changed the pins to counter bores located on the original pins.Added a second set of mounting points for 2.5 inch drive adapters.Without the pins it may be...

Installing an SSD adapter into your ANTEC Sonata hard drive tray is a straightforward process that allows you to boost your system's performance by leveraging the speed of a solid-state drive in conjunction with your existing storage setup. First,...

... cage slot. Use PC fan screws in the top and bottoms screw holes for alignment, and epoxy to hold all pieces together. Items to print: 1x top piece 1x bottom piece 2x side pieces Printable hard drive tray: https://www.thingiverse.com/thing:5111406

I upgraded my Antec Solution SLK Series Computer Case with custom hard drive rails, giving new life to an otherwise discarded SLK3700-BQE model that I had inherited. The case still had plenty of usable parts, but was missing some essential...

The hard drives mount from the bottom and are slotted so they can be adjusted to fit perfectly. I hope this design will help others fix their hard drive bay issues. The sides that slide into the grooves are about 18.2 mm wide. The overall width of...

Instead, this tray simply fills in the extra space in the HDD slot around the HDD to keep the drive from shifting left/right and up/down as well as stopping it from sliding too far into the drive bay and disconnecting from the network adapter. It...

They're simply too fragile and also really don't solve the issue of the drive sliding forward and off the sata/ide connector.Instead, this tray simply fills in the extra space in the HDD slot around the HDD to keep the drive from shifting left/right...

Large capacity hard disk drives (such as those manufactured by Seagate and Western Digital) use an alternate bottom-side mounting screw arrangement that is not compatible with the Antec Sonata III drive tray's mounting hole setup. This adapter plate...

I was still experiencing issues with shrinkage, despite having calibrated the printer. The problem persisted as the pins on the original part continued to pull closer together. Scaling my design failed to yield any improvements, so I decided to...

I had purchased a dirt-cheap used Fat (original) PS3 that functioned properly, but it lacked its hard drive tray and hard drive - I was looking to upgrade the hard drive anyway, so I crafted a custom tray based on a laptop drive that snugly...

I was low on space in my computer case, so I came up with a stackable hard drive tray equipped with 120mm fan clips. Each fan covers exactly three hard drives. Adding supports for the fan clips will yield a cleaner print, but it's challenging to...

This is a hard drive sledge for the Bigfoot XXL File Server. You need to print two per drive and the XXL file server holds up to 45 x 3.5" drives so you may well need to print 45. A special thanks to Lennog over at ServeTheHome for taking the time...

This is a TRS-80 drive face for my 5.25" RPi drive tray. It just glues on so, you can use it for ANY 5.25" tray. ... The face is slightly wider than the tray so when you glue it, make sure you center it.

This model stores up to 10 3.5-inch hard drives, engineered for rugged reliability and optimized for efficient filament usage. Permission is granted to modify the design as needed, but selling this design as your own or profiting from prints of this...

I fabricated a removable disk storage unit to match each of my machining equipment setups, with the intention that it could possibly be beneficial to someone.

Easy to print, faceplate for antec 300 optical drive.

hard drive

Couldn't get the holes quite perfect but with them being ovals I can get the screws in. ...Holds the hard drives very well just like the OEM trays and much cheaper and easier to track down than those

This is an incredibly easy solution to avoid shelling out $10+ for hard drive trays. It may not be as user-friendly or convenient as a standard tray, but it gets the job done just fine. ... Check out this video here: https://youtu.be/dINSZFLyLlk Print...

To build your own Raspberry PI NAS tray, follow these easy steps: Step 1: Print the custom tray design Step 2: Cut away the latch support as shown in the image below Step 3: Install your hard drive by pulling out the side latches and fitting it...

By adding a SATA extension cable to this drive tray, you can connect a 3.5 inch SATA hard drive externally to the server. This solution is available on Amazon. The SMAKN(TM) 22-pin (7+15) Sata Male to Female Data and Power Combo Extension Cable -...

UPDATE 12/14/2017 original upload was too small for hard drives. Fixed now. My first design, and I'm glad to share it with you! Despite being a newbie, I'm giving it a shot. I have eight 2.5-inch HDDs that just begged to be organized in style. The...

I removed the three CDROM trays from my standup server and wanted to fill it in with 2.5" drives. I printed this to allow that expansion of the drives. **This is a work in progress until I get it test printed** It *will* hold six 2.5" drives in the...

Excellent drive storage tray for a data recovery or computer shop. Must be printed at full size or it won't fit the drives. I used PLA+ at 215 degree nozzle and 60 degree plate temp and use green tape if you have a glass bed to minimize lifting...

I removed the three CDROM trays from my standup server and wanted to fill it in with 2.5" drives. I printed this to allow that expansion of the drives. This is a work in progress until I get it test printed Itwill hold six 2.5" drives in the trays.