antec 525 drive bay 3d models

The Nokia Lumia 525 is a Windows-based smartphone, offering users the convenience and functionality of the popular operating system. ...With its sleek design and powerful features, this device is perfect for those looking for an affordable yet reliable...

Adapter for installing a thin DVD drive together with a 3.5" card reader into a 5.25" port. The drive mount was glued in place. ... Print options standard 0.2 infil 10-15% support no

Instructions Removing the original parts isn't hard at all: Just remove the 4 screws that hold the cartridge bay from the base and take out the whole piece (alternatively, you can remove the whole baseplate for more free working space before...

Please let me know if you encounter any issues. These M2 / SSD adapters make it possible to mount two M2 SSDs or two 2.5" SSDs in one 3.5" hard drive mounting bay. Please measure the height of your SSD before printing the dual SSD adapter as some...

I'm searching for something to catch the photo spitting out of my HITI 525 printer. I need it to clip securely on and off. Designed using Fusion 360 and MS 3D Builder, this model is printed in PETG, but I'm still dialing in my printer settings.

This adds some security by clipping the rear of the board onto the drive.When you are ready to take the drive out for experimenting, just remove the IDE adapter board and slide the drive out!Print flat on its botton at .2mm layer height. ...preferably...

Getting Power to the drives can be achieved using a couple of these: 15 Pin SATA Male To 2 SATA Female Power Extension Y Splitter Cable Adapter Cable And SATA Serial ATA 15 Pin Male to 4 pin Female Molex Power Converter Adaptor Depending on your...

... secured to. All three MPCNC sizes are covered, generated from the same scad script. Crafted as part of my strategy to incorporate a powered drop table into my MPCNC build with an excessively tall leg. **Exclusive compatibility with 525 rollers!**

... ...I'm convinced it's still structurally solid, with tension focused on the mounting points and both drive and case, rather than the central beam. This design should print faster too. ... Thanks go out to usermod for coming up with the original idea!

To attach the brackets to each side of a 3.5" drive, simply use normal screws, then secure the bracket to a computer case with wood screws. I deliberately left out holes for those screws because securing locations can vary from case to case. ... The...

Here are some key details about this Nokia Lumia 525 Red model: - Geometry: - Real-world scale ensures accuracy. - Every object is complete with no missing parts. - All objects have only four sides; no complex polygons or isolated vertices...

The M350 case usually comes with only one bracket for mounting 2.5" drives and if you want to install a second one you'll have to print or buy an extra one.I usually don't believe in supplying presliced files but I am including some as you need to...

Adapter tray designed to fit a 2.5" SSD or HDD into a standard 3.5" drive cage or caddy. Important note: holes are intentionally precision-cut tight, allowing you to easily tap them with standard screws if necessary. Successfully fits Lenovo, HP...

Note that one end has a higher wall, so the drive will only fit properly over the lower wall end. This is a pair of 3.5 drive to 2.5 drive adapter designs. One uses a typical M3 nut (approx 5.3mm across the flats x 2.3 thick). The other is a simple...

POST-PRINTING Typical hole cleanup for clearance of M3 screws which attach 2.5 inch drive. In the tapped version cleanup and use an M3 tap if you have one. You can clean up the hole a bit an use an M3 screw to tap the hole, but be careful. If the...

This might not benefit everyone, but I attempted to fill an open slot in my PC's casing, originally designed for a floppy disk. ...The fit was precise and snug, so it might not be compatible for others.

These designs can be easily machined from 1/8 inch thick acrylic using a laser cutter. The tolerance of the cuts is extremely fine, yet they have still managed to create successful prototypes despite issues caused by protective plastic sheets which...

Super basic HDD holder for 4 HDD's.

<p>A fixed version of gudenau's file with correct dimensions for 3d printing with no need for scaling or fixing the STL file :)</p>

Should fit 2 70mm fans, tested with Startech units and they fit fine. May require some mild cutting in the event of clearance problems. Would suggest printing face-down, with only supports in the center. ... And also scaling it down 10x.

The new design features more space for creating single-sided PCBs, utilizing an ATTiny2313 microcontroller instead of the Tiny Cylon's counterpart due to its four PWM pins for enhanced functionality. ...This updated version also boasts a double-sided...

Slight remix so it can go on keyring

A finely tuned rendition of Gudenau's creation is now available, accurately proportioned for three-dimensional printing, thereby eliminating the need to adjust or resize the STL model.

Included here are: - a blank - one with a 35mmx12mm hole suitable for one of those SD card re-locator devices so you can have easier access to the SD card. - one with the above 35mm x 12m hole & 2 slots to mount 2 panel mount USB type-A  ports.These...

Just a simple design, sharing for some folks on reddit. printed with the front facing down, with supports. ...may need some fine tuning with a knife to get a good fit in the case

Here is a PC-mounted adapter holder that lets you plug in your Nintendo Gamecube controller on your gaming machine.

To modify the Marlin software, I configured the FAN output to a 5-volt TTL PWM logic level on the RAMPS 1.4 board since I drive the RAMPS at 12 volts. The D9 output would have damaged the diode driver otherwise. I will provide more information on...