anschutz rail to arca 3d models

Revamped Telescope Dovetail Rail for iOptron to Meade 8-inch SCT. The mount's plastic construction led to broader mounting points compared to standard ones. Although not ideal, it was an improvement over the previous non-existent setup. Wishing you a...

... (2015-to early 2017 models). ...Per pair, you need: m3 x 55-60 mm screw m3 thread insert 10-11 mm washer 14-15 mm washer I recommend from 2 to 4 pairs to be placed on the rail. ... Also check https://www.thingiverse.com/thing:4336323 for the Y axis

This Clip attaches directly to the accessory rail of your Nerf Gun and links it to a standard camera hot shoe adapter, making it easy to mount the Triggertrap Phonetrap above the barrel for creating immersive, first-person shooter-style videos from...

I required a mount for two linear rails to sit atop a 2020 aluminum profile, specifically designed for my Anet A2 printer. I took gkirdeikis' design as a starting point and remixed it: https://www.thingiverse.com/thing:3199345. ...To increase...

The mount to the rail is screw-free. The yyh1002's modular arm system still requires screws, but that's where my V-Slot Rail screwless adapter comes in - for easy removal and movement on the printer. Remixed yyh1002's Modular Mounting System with a...

M5 sized holes.You will need to print two tabs for this design.They can be found at: https://www.thingiverse.com/thing:3401942 orhttps://www.prusaprinters.org/prints/8512-din-rail-mounting-tabPrint SettingsPrinter Brand:Prusa Printer: I3...

Red Dot Sight Adapter - Astro Dovetail to NATO Rail To be mounted in Astro dovetail shoe with 34 mm base. (Foot has 32.5 mm base width and 60 degrees flank angle.) Provides NATO/Picatinny/Weaver-compatible rail for mounting a standard red dot sight...

Connect your Raspberry Pi to a 35mm x 7.5mm DIN EN 60715 rail with this clip; however, you'll need to print out two of them for both ends. ...The full clamping force is achieved through deformation by the bottom screw.

There is no outer barrel as the suppressor is glued to the rail. The rail I used is here: https://www.thingiverse.com/thing:2253858/files I would recommend printing the rail at about 102-105% as it is a tight fit onto the adapter. Hopefully all...

DIN Rail to Spray Holder (a bike bottle holder) using bike bottle holder for 400 ml spray (0,5 Usd) Print instructionsCategory: Organization Print Settings Rafts: No Supports: No Resolution: 0.2 Infill: 15

If you're using a Tevo Tarrantula frame and your X-axis belt rubs against the rail edge, consider adding this setup to minimize belt wear. Update: A new design now accommodates 4mm PTFE tubing. ... Update: Improved print quality is achieved with our...

Was having a hard time making the end cap work with Ender 3 v2 and ender 3 v2 neo, this idea is a hood over the corner. ...Has a through hole to allow a t-nut through the top rail. ... Falls off less than the original.

(This keep me from having to design and print a lot of single use parts.)You will need to print one tabs for this design.They can be found at: https://www.thingiverse.com/thing:3401942...

Instead of relying on a pre-existing rail pattern, I accessed the original drawing and reconstructed the design using Solidworks to better understand its specifications. To produce this unit, I utilized my 3D printer, printing it upside down in PLA...

I created a custom casing for my Dimplex TRS120 Towel Rail, specifically designed to secure the electrical connector and neon bulb in place. Given the high cost of these components, I decided to design an alternative that closely resembles the...

I'm modifying a Vex system with a 1/2" hex shaft, requiring me to connect it to an aluminum rail using 1/4" screws in such a way that I can attach a potentiometer to the end of the hex shaft to track its position accurately. ...The compression force on...

This is a VERY CRUDE adaptor plate to fit the Mean Well RSP-500 to DIN rail. All credit for the design go to the Voron team, i just extended the ends and added holes. You will need to print two, settings I used were standard Voron print 0.2 LH 4 x...

... (2015-to early 2017 models). Per pair, you need: m3 x 55-60 mm screw m3 thread insert 10-11 mm washer 14-15 mm washer I recommend from 2 to 4 pairs to be placed on the rail. ...Also check https://www.thingiverse.com/thing:4336323 for the Y axis

WTF rails on the Onewheel+ XR drops the platform relative to the axel and ads a 3 degree angle. This makes the stock fender not fit anymore. This adapter fits between the stock gasket and stock fender to raise it above the wheel and provide a flat...

I only repair reinforced rails because they fail me more often than propellers.

Mount a 45-Degree Picatinny Rail directly onto your trusty Nerf Rival Blaster.

... ensure secure assembly, M3 brass inserts and matching M3 screws are required. Upgrade to the latest version 2 for effortless compression mounting capabilities - explore the enhanced details on Thingiverse at http://www.thingiverse.com/thing:1697844

Keep in mind that the modified rail is delicate, so make sure to adjust its placement so the engine doesn't touch the bridge - it's a pretty tight fit. Because of this issue, we've also created a 3/4-sized version (you'll need two for double-decker...

I want to attach a laser sight and a small scope, but the Baikal MP-651K only features a small dovetail mount under the barrel. It is made with Tinkercad, so it could be a litte off here and there, but it works and fits like a dream. ... PIctures...

Mount your phone to an Arca-Swiss compatible tripodI combined the extended version of JakeJake's phone mount with the Arca Swiss plate by JohnClarkThe slider and knob are unmodified from the original design1/9/2023 update: Several people in the...

Insert or mounting to fit a D1 Mini (ESP8266) + RS485 to TTL converter in a din rail housing. All contacts are free to use. I use it to connect a KWH meter with RS485 (modbus) interface to my domitica system. ... Dinrail Housing:...

... mounting. M3x10 screws fit perfectly both for mounting the mount to the clip and the board to the mount. ... The specific board I use is from amazon, called "1-3KHZ 0-10V PWM Digital Analog Converter Module, PWM to Voltage Converter Module".

For each pair, prepare the following components: * A M3 screw measuring 55-60 mm in length * An M3 thread insert for precise attachment * Two washers: one with a diameter of 10-11 mm and another with a diameter of 14-15 mm It's advisable to install...

I slightly adjuted the fit of the base plate and added a glider to fit the Makita rail. I printed it in two parts and glued them together in place, because the support proved impossible to properly remove from the gliding part. Maybe you got better...

This phone cradle fits snugly onto the R60 rail cover that I crafted with ease. ...It's a straightforward component, unadorned yet effective in its purpose - securely holding two phones in place along the rail.