anne pro 1 3d models

... too, as long as they are larger than 3mm. I believe the screw hole layout is identical for the Anne Pro 1, but I am not able to test this. Approx size is 307 x 119 x 27 mm. ... I have included a split version for those with smaller print beds.

For those looking for an ultra minimal and low profile case for their Anne Pro 1 or 2, I've created this. This is a zero degree case, that dispenses with the battery, so ideal for people who always use their keyboard wired. Short of removing the...

A simple rest to fit the Anne Pro 2 stock keyboard, I wanted to keep the angled look of the keyboard, so I've tried to match the lines as close as possible. There are spaces underneath to fit rubber strips if you require, the holes are 2 mm depth,...

For those seeking an ultra-minimal and low-profile case for their Anne Pro 1 or 2, I've designed this sleek solution. This zero-degree case eliminates the battery compartment, making it ideal for users who consistently connect their keyboard via a...

...I have not tested it on the Anne pro 2, but the screw locations are the same between the two keyboards and it should work. It prints on a 300x300 printer like the CR10 if you rotate it 45 deg. ...This will NOT work with a standard GH60 type keyboard.

This keyboard is a prime candidate for the Anne Pro 2's protective features. ...Providing vital safeguarding capabilities whenever you're on-the-go with it.

... thanks to two 1-pound command strips that effortlessly mounted each piece. Note that this accessory is specifically designed for the original Anne Pro but may also work with the Anne Pro 2 - I just don't have access to one for testing purposes.

I wanted a simple rest that would fit the Anne Pro 2 stock keyboard perfectly, so I aimed to maintain its angled look by closely matching the lines. To add flexibility, I've left spaces underneath for rubber strips if needed, and carefully designed...

This is a cover for my Anne Pro 2 mechanical keyboard. Should also fit any 60% keyboard of the same size (292mm x 102mm outer case dimensions). This cover is to keep the dust out when not in use. I got the idea from a Cougar TKL keyboard that came...

... Anne Pro 2 and may not fit other wires effectively. If you want to create your own, here are the measurements I used: Anne Pro 2 Type C: 12mm - Sides 7.2mm - Top 16.5mm - Long Extrusion 3mm - Bevel Other Type C I found: 5.8mm - Top 10.3mm - Sides

anne with an a

I'm kind of glad I got a chance to get some of these tables out where people can see and even make if they like the look.Print settings for photographed model using PrusaSlicer-2.3.1 based on Slic3r:0.30mm DRAFT Infill: 20% Generic PETG(3) -...

I'm eagerly awaiting a test print of this innovative Anne Pro Mechanical Keyboard Case, boasting a sleek Floating Keycaps design. The challenge lies in its current size, which exceeds my modest 3D Printer's build volume. I plan to dissect the model...

It's for my close friend Anne.

http://www.thingiverse.com/apps/customizer/run?thing_id=62719 Instructions Using the following options: ring_radius = 3 length = 50 width = 25 text_size = 6 text = Anne build_plate_manual_y = 100 build_plate_manual_x = 100 height = 1.5 lip = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=175150 Using the following options: letter_spacing = 2 slitwidth = 4 line_spacing = 2 font = write/braille.dxf fontsize = 12 text_style = 25 slitlength = 12 line_10 = corner_radius = 3...

Anne, a close friend of mine at RCT, was meticulously designed using the versatile tool SketchUp, and her dimensions are precisely 168 millimeters in length, 50 millimeters in height, and 20 millimeters in depth.

Set the Z axis at 0.5mm to 1.0mm height. To reduce rattle, you may stack two 0.5mm inserts. Print with a brim for maximum adhesion. WARNING: Care must be taken while cutting the excess material off as you may accidentally cut into the print...

'Anne' is a friend at RCT. Designed in SketchUp with Arial Blk font. ...It is 168 mm long x 50 mm high x 20 mm deep.</p> <h3>Print instructions</h3><p>No rafts / No support</p> <p>0.3 mm resolution at 15% infill</p>

The customized version of this design can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=52734, featuring a font thickness of 5, stick thickness of 3, hole radius of 3, using the orbitron.dxf font for the message 'Anne', a stick...

... ...To print, use settings such as clip 2, scale 1.0, adjust 0, layer height 0.3, ring 10, build plate manual Y and X positions set at 100, g code setting of 0.2, trim off, seed number 12031958, minimum thickness of 1, and build plate selector set to 0.

http://www.thingiverse.com/apps/customizer/run?thing_id=507810 Instructions Using the following options: custom_overhang_width = 1.6 custom_back_extra_port_corner_resolution = 8 custom_bottom_port_length = 40 phone_model = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=74322 Instructions Using the following options: picture_shape = standard include_hole = yes text_line_5 = text_line_4 = text_line_3 = text_line_2 = text_line_1 = text_vertical_position = 0...

Anne Pro 2 60% Compact Gaming Keyboard Modelled to exactly fit a reference picture of an Anne Pro 2 60% Keyboard. ...Includes: RGB Plate Base Keycaps object

This is a replacement shell for the Anne Pro 2 keyboard. If you would like to upgrade to a bigger battery, check out this version modified to take 3x 18650 cells (https://www.thingiverse.com/thing:3698815). ...Or this minimal low profile version...

*16/05/20* Upgraded the design with a Tofu case-based version\r\n\r\n*08/04/20* Released an updated version based on the Model F62 keyboard\r\n\r\n*Update 3:* Introduced additional versions for users seeking a distinct appearance.\r\n\r\n*Update 2:*...

Published by 3ds Max

No description provided.

Print this text for miniature purposes, such as scale models or dollhouses, to exhibit your printing prowess. Utilize a Replicator with skeinforge 47 and disabled acceleration; in Dimension settings, set "Extra Restart Distance" to 0 for precise...