annabelle pocket camp 3d models

I've included the magnet pockets on the short sides even though they don't really work with the angled corners. There just isn't room on the corner piece to have magnets. I've printed some of these but haven't gotten around to painting them yet, so...

The bottom sides of the support arches have locating pegs that fit in one of several pockets that are found in the rails. This gives some adjustability regarding the angle that the filament enters the bulkhead fitting and thus reducing the friction...

Width is the length along the X axis; depth is along Z/Y axes (remember the orientation thing we talked about), which is how much does the tab protrude from the marker cap, in protruding-from-your-pocket direction. Set any of these to 0 to disable...

Note that the wheel is designed so that a ball will sit just a little bit proud when it is being carried in the lift pocket. This means that the wheel doesn’t need to be slammed up against the clock. It also means that the balls will be captured...

The lamp was originally published at thingieverse and here you will find all you need including several additional shade themes. I found the excellent shape computations for the cylinder not on wikipedia, but, (with my fathers help) in an Austrian...

Screw the slipring adaptor into the center hub using stianless screws in the recessed pocket, and then screw the slipring over it, making sure the spinny around part is inside the reel. Route the static wires into the back box. Now glue or tape the...

... a small optimization to the tool holder module (for the small hex wrench).  The current version is ver1.4.  The image below shows the modification which increased the pocket for the small hex wrench by a small amount. ... The clip was also widened.

The motion of the Slide moves the Hammer via small bosses in the Slide, keeping the Rotor free to turn. The Rotor is the square notch style from the bakewell remix, to which I added a flange on both sides to keep it centered in the Slide. Changed the...

Note that the wheel is designed so that a ball will sit just a little bit proud when it is being carried in the lift pocket. This means that the wheel doesn’t need to be slammed up against the clock. It also means that the balls will be captured...

The plastic pocket is removed from the original power supply and the connector for the 220V power supply is disconnected and screwed to the rear panel. The cables lead through the right side to the printer. Attention, this is a part with a length of...

 Not pocket change, but these are quality parts that won't disappoint.  The MagTag packs a ton of capability into one part.  Hit a sale or promo and it will be cheaper.  You could pinch pennies on a different CO2 sensor.  It...

Printing tips: BASE: I printed the base with supports but used an overhang angle of 85% to avoid supports in the enclosed pockets. There is really only one place where the base needs supports and that is the flat area just above the opening in the...

Screw the slipring adaptor into the center hub using stianless screws in the recessed pocket, and then screw the slipring over it, making sure the spinny around part is inside the reel. Route the static wires into the back box. Now glue or tape the...

They have cutouts for zip ties.The V2 is lighter but weaker; I wanted to put some carbon strips on it additionally for strangth; normally just print the regular versionOptionalFC Cover Covers the FC stack for added protectionESC CoverCovers the...

Place the topcard piece (with each pocket loaded with 5 pennies) on top of the deck.Operation:The trigger piece has a nub on the end which pushes the deck up away from the eccentric feed wheel. When the trigger is pulled, the deck drops down in...

the only downside many have noted is their impeccable speed, earning them the nickname "Pocket Rocket('s)". This custom chassis was made as an alternative if you wish to spice up your already existing shells or shells you wish to design and make. as...

I used a nail file and then a pocket knife. --Insert the feet block into the legs assembly, so that the feet are flush with the outside edge. The locating pegs on either side should be at the top, while the feet are at the bottom. Align the locating...

Insert the 4 remaining nuts into the pockets on the head of the Neck. Thread the thumb screws or bolts into these nuts. As the screws tighten the Pads press harder onto the Tuning Pegs increasing their resistance. Glue the Medallion onto the...

Very useful for the "Thumbless" versions where velcro attachments becomes more difficult trying to route a thumb through the palm pocket too. This is an excellent example of thermoform PLA : http://www.thingiverse.com/thing:403001 EDIT 18/09/2014 :...

The pocket for holding the slim magnet requires that your printer should be capable of modest bridging over a reasonable distance. Parts were designed for printing at 0.3mm layer height, with 0.6mm wall width, but should also print well at finer...

...However, the Daemon invasion and the War of the Lords shattered this equilibrium, and after Tialevor betrayed her and Duum, the Lord of Blood and War, she and many other Lords were confined in a planar prison, confined in other pockets of existence.

The shorter/wider side snaps into the corresponding pocket on the shaft, and serves to index the tube holder to the shaft. I put a dab of super glue on the nut before snapping it in to the shaft.The magnets should just snap into the holes on the...

I searched all over the internet until I found a perfect remix called the “Slack Lack” (Reddit & Thingiverse links). The original designer nnorton00 incorporated these clever sliding-hinges that allow the doors to tuck back inside the enclosure...

Put this magnet in the display magnet pocket. Put display part over the body and test that magnets atract each other. Secure this magnet in place with a drop of super glue. Now is time to glue Olaf lithophane into the display body. Do it according...

as such the hinge portion may be a little weak and hard to print cleanly, Shouldn't cause an issue if your goal is just showing friends and displaying on a shelf but surviving in a pocket during a convention is a whole different task. If requested I...

(to prevent IR LEDs reflection)Step1: Make the Base section.Open the "Unifi G3 Instant_Case_Base" STL file in Cura.Set the Infill Density to 100% (for best water-resistance).No supports are required for this part.Slice it and in "Preview mode" make a...

I used a nail file and then a pocket knife. --Insert the feet block into the legs assembly, so that the feet are flush with the outside edge. The locating pegs on either side should be at the top, while the feet are at the bottom. Align the locating...

Use a 6-32 nut and bolt to attach the clamp around the body of the Cam 3 (the nut goes in the hexagonal pocket as a captured nut). To attach the Cam 3 to my 3D printer, I used a T-nut and bolted it directly to the 3030 aluminum extruded frame. ...

No more fumbling to find the volume keys on a phone that's tucked into your pocket. Just click. And flip.</p><h5>Technical Details</h5><p>I didn't have a Teensy handy at the time, so I substituted a Keeyees Pro Micro (which Arduino sees as a...

Also, I removed the nut pocket for the radiator. It was too hard to use with hex nuts. Since Heath generously included his Fusion source file, I remixed it to fix these issues. You'll still need to print Heath's mount lock, if you don't use my...