anime thick 3d models

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

Anyway I like the idea of adding animal faces on the arm sides, so I made three version out of this: Plain, no-faces, Blumrich's original interpretationOne face per armFour faces per arm, one in each direction, like it was described in the Bible...

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">

Instructions Using the following options: thickness=1 nozzle=.4 holeRadius=2 target_diameter=80 scaleFactor=1 steps=6 wide=5 branchy=5 sharp=8 full=5 fuzzy=5 ringed=5 scaleFactor=1 random_seed=2800985 thickness=1 custom_seed=0 long=5 fat=2 organic=3...

So I fired up Fusion 360, grabbed my shelf-clip bracket (which fits great on my 25mm thick desk/hutch top), and created a new project: the one-piece Bose QC35 Headphone Holder. I fiddled with geometry and fillets to get things to look nice and fit...

The thickness is not critical, but 0.5mm is easy to work with.200mm velcro battery strap: from HobbyKingOptionally, a little strip of velcro to anchor the battery tray to the lightboxTools:Soldering ironTin snips and file/sandpaper for cleaning up...

The previous stated M3 screw lengths take into account the thickness of the "Led Stripe Holder for Petsfang Ender3/CR-10" (they were two (2) M3x22 and one (1) M3x18 with M3 nut). The upper right corner of the 4010 heat sink fan DOES NOT have a...

A personalized version of http://www.thingiverse.com/thing:50123 was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=50123, with specifications including 6 hearts, a ring thickness of 1.6, a ring width of 7,...

The planet of the homonymous Netflix cartoon (Centaurworld), this was based on the intro animation, and the space view from fourth episode. I scale it using the "glare" of the terminator line, assuming its sun it's a red dwarf (because it's seen...

There are practically no loads when processing small surfaces, so the plastic sandpaper holder is quite convenient.The shape completely repeats the original tool, except for the thickness, for plastic I chose 8 mm.The video shows the first build, but...

It was with the help of a laser that I did it quickly from a 2.5 mm thick acrylic sheet and a 25 mm diameter acrylic tube. But STL files are also added for implementation on the printer, although it's long on the printer...

Since I mainly use it for soldering electronics, there is a situation where you need a slightly smaller scale to get an image, but it magnifies too much that only one SMD detail is visible on the screen with the microscope fully raised.The column...

I think the rotor ideally will be able to rock back and forth on the mouthpiece cone by about the thickness of a piece of paper without bottoming out flat on the mouthpiece but am not 100% certain if that is optimum spacing but it works well and a...

Can be cut with a scalpel ...On the connector pins, the XT60H cut grooves 1 mm thick and 2.5 mm deep to fit the Type-C board in them, thereby reducing the length of the entire structure and giving it rigidity.Then everything is simple, fill in with...

I also tried to cut solid wood 8 mm thick, as a result, it almost cut through, but without blowing it was difficult. As I said in the video, you can watch everything:</font><br></div><br> <div> <a href="https://youtu.be/Q-GMlKHZMQI"...

Link: https://www.thingiverse.com/thing:5178820 2021/11/21: I'll start by mentioning that I went ahead and added the mirror of the skullcap canisters and made a minor adjustment to shrink the insert as my first print came out too thick. Secondly,...

The thickness of the foam rubber is 2 mm. There are also different lengths of nuts for collets, and I made this project for the one I have available. But if you have other dimensions, the project has attached files in STEP format, which you can...

You will need an anodized aluminum tube with a diameter of 8 mm with a wall thickness of 1 mm, as well as a UNC 1/4-20 tap, this is one of the standards of carving used in photo and video equipment and accessories. It is convenient to cut the thread...

I think the rotor ideally will be able to rock back and forth on the mouthpiece cone by about the thickness of a piece of paper without bottoming out flat on the mouthpiece but am not 100% certain if that is optimum spacing but it works well and a...

http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options: grid_size = 3 thickness = 1 pixel_size = .4 pixel_shape = round(.04 * 6.25) orientation = down pixel_elongation = long border_width = wide...