angled gpu mount 3d models

I had to position my Ikea Tradfri Motion Sensor at a fairly steep angle, pointing downward so it could clearly capture the bathroom area and give me a good view of the shower's glass door.

... a remix of [RT3DWorkshop](https://www.thingiverse.com/rt3dworkshop/designs)'s [design](https://www.thingiverse.com/thing:4828390). ... I've just added a -25° angle because I'm on the 2nd floor, and changed the slots to fit my very thin hanging strips.

The Apple Magic Trackpad 2 is elevated at a precise 10-degree angle, allowing users to easily tilt it to either side for optimal use. ...This subtle adjustment makes navigating with the trackpad instead of a traditional mouse feel remarkably more...

Simple bracket which allows you to angle the extruder 20 degrees, so that the bowden tube doesn't get in the way of the rods or get stuck in the endstop. Needs an extra M4x10mm bolt and a M4 nut to install. Category: 3D Printer Parts

This device attaches securely to a wall to support an Oculus Rift sensor at an optimal angle, allowing for unobstructed access. ...For added stability, simply screw in a 1/4-20 by 1/4 inch bolt readily available at any hardware store.

Redesigned to perfection, this innovative solution features a cleverly crafted angled hole that securely locks into the wall, effectively preventing any unwanted rotation. ...By doing so, it boosts the overall holding power to keep even your most...

Made this remix so I could use M6 nuts and bolts (which I have in abundance) to mount the stock spool holder to the mount and use the T nuts to anchor the mount to the frame. Also added a second frame mount hole because personally, I believe in...

Extended version of my other remix, meant to attach a 4020 radial fan mount I remixed (https://www.thingiverse.com/thing:4818990). ... Also made the tab extend out in both directions as it will be even stronger and I do not have the stock shroud mounted...

The Human Mount is a custom design that takes inspiration from sabihalejandro's popular creation, the Mount. This new iteration is specifically engineered to attach seamlessly to the Armattan Chameleon Camera Plate. ...Additionally, it features a...

... 2 pan head bolts. (M4 or M5 size.) - For M5 nut/bolt, drill out holes. - After mounting you will have 40mm of play, for sliding to best position, before tightening. ... * 4-8-22 - fixed for better fit, added version with picatinny extensdion

... expects the wiring to be more or less in the center of the slat. You will need some longer mounting screws, but I coutnersunk the mounting holes so decking screws will work perfectly, but need to be at least 2" (5cm) long. Category: Outdoor & Garden

Enjoy the use of an extended spool mount that accommodates larger spools by following these instructions. ...To do so, print part 2 and attach an approximately 8mm diameter rod - then experience enhanced functionality!

I liked the idea of moving this mount down low due to having problems with the original top Spool mount. The goal was to get a smooth "pull" off the spool, and widen/stabilize the base of the mount. Please let me know if you have any issues with...

For the Thomas Scherrer TX700, mount a bracket onto the Turnigy 9XR's back. The bracket can be printed on an Ultimaker 2 with 10% infill and 1.5 mm shell thickness, taking approximately 30-45 minutes for custom fast settings. The JR bay won't be...

...This mount securely attaches to the screw holes of the four poles, weighing only 6g in PLA material. Print Settings Printer: Print-Rite DIY Rafts: Not Required Supports: Yes Notes: The Supports-Standard setting was used as a default from my printer.

This is essentially a replica of user PrintedFirearm's design, "GOPRO Picatinny," minus the etched detail on the mount's neck. ...To eliminate the etching, I inserted a wedge-shaped cutout, followed by refilling it with another wedge, all of which were...

A sleek new design for a wall mount allows users to neatly route their USB cable directly through the sensor holder's rear opening, keeping cords organized and out of sight. ...An upgraded version, V2, is now available on Thingiverse at...

Mobius Mount with an additional 8 degree tilt, compatible with the emax / nighthawk style mini quad frames. Two versions available, one with a small hole for zipties, and one without. ...Holes will fit a small ziptie - two should be enough to wrap...

... I enlarged the slanting support components to match the complete span of the design. To install, print two units and affix them on your Printer's upper thread rods. Place your spool atop with a smooth or threaded shaft for secure mounting.

... slat, as this will make installation much easier. You'll need longer mounting screws for this project, but I've countersunk the holes so regular decking screws can be used instead - just be sure they're at least 2" (5cm) long to ensure a secure fit.

If your IP cam is on an elevated position and you want to be able to view more of the bottom this support/mount works perfectly. It uses a 6mm screw to attach the camera and there's also a screw attachment on the bottom if you want extra security but...

If your IP cam is on an elevated position and you want to be able to view more of the bottom this support/mount works perfectly. It uses a 6mm screw to attach the camera and there's also a screw attachment on the bottom if you want extra security...

The mount is designed to attach securely to the frame pillars, providing a solid base for your quadcopter. A cover is included for minimal protection, while allowing easy access to the dip switch and cable attachments. The LED channel lights are...

I found the stock and traditional mounting options for the tape switch on one of my rifles to be completely off-base and decided to harness the versatility of the monolithic rail to position the pad exactly where my hand rests naturally when...

If your IP cam is on an elevated position and you want to be able to view more of the bottom this support/mount works perfectly. It uses a 6mm screw to attach the camera and there's also a screw attachment on the bottom if you want extra security but...

Hey guys, I just wrapped up a sweet vertical GPU mounting mod on my YouTube channel and I'm stoked to share it with you! This custom setup was tailored for my Phanteks Enthoo Pro M acrylic case, but don't worry, it's totally adaptable to fit other...

Content x1: GPU support (different models) x1: Foot GPU / Video Card Support - PC Gaming! Characteristics: 9 positions in its length to be able to adjust it to any type of GPU Adjustable foot in height and position for perfect support 210mm long 3...

New version of this make can be found here --> https://www.thingiverse.com/thing:3475590 This is a 3D printed Vertical GPU Mounting Bracket that's designed with precision. You won't need to make any modifications to your case, which means you can...

Please note: I designed this specifically for the NZXT S340 Elite case and requires cutting of some metal, as a result I have no idea if it would work for other cases (however as they're all mostly the same at the back, it should work fine - maybe...

Remixed this for the pattern of my risers. ...Hole layout on mine center to center is 1.071" x 3.786" After printing, tapped the holes 6/32 and used case screws.