anet fan 3d models

... compared to any of the layer shift versions. The fan mounts directly on the stock blower in its usual spot on an ANet A8. ...You'll need to turn your heatblock 90 degrees so that the heating element and thermistor face rearward from the printer.

This is a custom fan duct design specifically tailored for the Anet A6 Titan mount by Xalky. https://www.thingiverse.com/thing:2459756 The round shape of this duct enhances air distribution significantly. V5 requires resizing to 10% (or 90%...

I tried several models of ducts I found here on Thingiverse, but it would appear that my part cooling fan has a larger opening than any of the models I found here, because none of them fit. That said, This model that I made from measurements of the...

This remix combines elements of FranciscoLupin's Titan Aero Carriage for Anet A6, specifically adapting his fan spacer/autolevel sensor mount to accommodate a BLTouch. By shortening the original design and incorporating support for two M3 screws, I...

We at VintageElectronics.ca immediately noticed a problem when we started using our new Anet A6 (a Prussa i3 clone) - the Y-axis stepper motor overheated during prolonged printing at high speeds, causing the nylon belt to stretch and eventually...

Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: .20 Infill: 40 Notes: The print took about 30 minutes. Post-Printing Refer to SentinelRX5's post for step-by-step installation instructions. ...Make sure to install the mount onto...

Support for BLTouch on ANET E10 \r\nWorks with original ventilation block only.\r\nConfiguration guide available at http://www.latelierdufrdd.fr/2017/12/13/installation-bltouch-sur-anet-e10\r\n\r\nPrinting from 0.2 to 70%\r\n\r\nPrefer using M3...

Anet A8 Extruder Fan wide open, adjustable handle securely attached for automatic leveling sensor precision. ... I carefully placed the M2 nut in position beforehand, having learned from a previous oversight when I failed to secure it properly.

I crafted a custom fan cover based on Zadthebad's original design, scaling down the opening to accommodate an 80mm fan while relocating the mounting holes for optimal compatibility.

The original fan cooler has been improved and replaced with an upgraded model. ...It takes the place of the original one without discarding the metal block, requiring only the replacement of the existing fan with a radial type of 40mm.

A High-Tech Power Supply Fan with a Twisted Twist - A Tornado-Shaped Cover Gives It a Cool, Futuristic Look

As some of you may know newer versions of the Anet A8 have slightly change the PSU cover, mine was made in March 2020 so I had to make some adjustments to the model made by Leo N. If you are not sure if the model will fit your PSU I made a test...

I've been using the standard model for several months now, but I've never been a fan of how the fan is mounted with just two screws, along with the noise level being a major issue. ...To address these concerns, I decided to upgrade the design so that...

... inside a 40x40x11mm box could be used instead. The bracket will securely attach to the motor using the screws provided with the printer, and the fan is mounted to the bracket via 4mm self-tapping screws, which usually come included with your fan.

I cut the original fins and printed a whole new set of fins for radial fan and a whole case. Glued the fan with hot glue. Working like a charm. As per suggested, uploaded new fins design with smaller rim for better air intake. Update 31/10/2017:...

The nozzle fan for the E3D carriage was created by a talented individual named Toosha, and we're grateful for his contribution to the community.

I removed the fan cover and slightly recessed the screw holes. ... The extruder offset values are set at x: 8mm and y: 53mm.

An 18mm sensor mount is designed to accommodate 30mm fans, specifically engineered to screw into the E3D V6 30mm fan. Designs made to fit this application require careful consideration of the mounting offsets. ... For version one designs, the necessary...

Printer Settings: Printer: Anet A6 Rafts: No Supports: Doesn't Matter Resolution: 0.2 Infill: Honeycomb 20% Notes: - Use a low printing speed for better results - it reduces warping and curling. ...- Depending on your setup, you may want to use a brim...

I chopped up the original fins and designed a whole new set of fins to fit a radial fan and a full case. Then I glued the fan in place with hot glue. It's working like a charm. As per your suggestion, I uploaded a revised design for the new fins...

- I made a cutout in the air deflector of the fan to pass through the reset button (https://www.thingiverse.com/make:371277) - I added a 3-position switch: - Position "0": Ventillo motherboard and FAN 2 (nozzle) turned OFF - Position "1": Ventillo...

Improved Circular Fan Duct for Zeus X-Carriage Discover a more efficient way to cool your 3D prints with this cutting-edge circular fan duct designed specifically for the Zeus X-Carriage. This innovative design features a partition wall that ensures...

Mounting Bracket Simplifies Installation of Ramp Systems and Cooling Components A user-friendly mounting system designed specifically for the Ramps 1.4 mainboard, a 60mm fan, and an optional MOSFET board. ...This bracket streamlines the setup process,...

I added some passive coolers to Pi3 and an active fan, which is controlled by a script through GPIO. As a result, you can see a transistor next to the fan. ... Update 2018-01-27: I made the spacer 1mm taller for better clamp distance to soldering...

The original fan duct for the Hesine/M505 series of printers is specifically designed to meet the unique requirements of these machines. When it comes to printing settings, here's what you need to know: Printer Brand: RepRap; Printer Model: i3;...

I added a slot on the bottom of the front of the front mount, and a tab on the half moon shape fan nozzle to hold it in place. Fixed v1 of the front, was missing slot Added v2 of the side which adds a recessed hole for the nut for easy tightening...

I modified the bottom of the front mount by adding a slot, and I also added a tab on the half-moon shape fan nozzle to secure it in place. Fixed Version 1 of the front mount had a missing slot. Version 2 of the side was added, which included a...

Originally borrowed from http://www.thingiverse.com/thing:1620630 by Hesine M-505, Anet A8 - Center Nozzle Fan designed by Arjjck and licensed under the Creative Commons - Attribution - Non-Commercial license at...

Instead of removing the screws from the fan, this method uses magnets to hold the baffle in place on the PSU. The exhaust then flows out to the rear of the PSU. ...So far, it's passed some short-term tests, but I'd love to hear about your experiences...

Instead of removing screws from the fan, this method employs magnets to secure the baffle on the PSU, redirecting the exhaust gases to the rear of the unit. ...Please note that this solution hasn't undergone extensive long-term testing yet, so please...