anet et4 parts 3d models
630308 3d models found related to anet et4 parts.
thingiverse
3) Sustituye los tornillos M5 de los rodamientos auxiliare de la correa por los M5x30, introduce en ellos los rodamientos y enrosca una tuerca en cada uno para fijar el rodamiento en la parte superior. Vuelve a enroscar los tornillos hasta el final....
cults3d
...3) Sustituye los tornillos M5 de los rodamientos auxiliare de la correa por los M5x30, introduce en ellos los rodamientos y enrosca una tuerca en cada uno para fijar el rodamiento en la parte superior. Vuelve a enroscar los tornillos hasta el final.
thingiverse
Update 22/05/2020 This is an adaptation of the cable protector for the heated bed, featuring a cable diversion to one side along with an added chain of balls that extends into the box interior. - Print approximately 17 chains of balls. - Print 1...
thingiverse
Improvement of the Correa Y Tensor (https://www.thingiverse.com/thing:4256306) by Matosantos, with the possibility of adding a later switch for LED lights. Fewer screws and nuts are now required since everything is based on the same material used in...
thingiverse
I printed it with 0.6mm nozzle with 100 infill, it's pretty solid. The motor is now better supported. ...you can even use the stock screw's (i made the screw wall thinner for that)
thingiverse
Despues de partir dos veces el modelo original he realizado una modificación para darle un poco mas de fuerza a la estructura. ... Espero que sea de utilidad.
thingiverse
Remixed from sima35 design, as the mean well fan is too wide for this design and the fixing holds to is 22mm instead of 20mm apart. I use this as a conversion from side fan to blowing to mainboard directly. I only recommend using this design if...
cults3d
This accessory for the layer fan is a modification for the Igneus v2, here you can find it: https://www.thingiverse.com/thing:4178590 Necessary: -1 Screw: M3*15mm -2 Screw: M2*10mm -1 nut: M3 -2 nut: M2 This access for the intake fan is a...
thingiverse
This accessory for the layer fan is a modification for the Igneus v2, located here: https://www.thingiverse.com/thing:4178590. ... Required: - 1 Screw: M3*15mm - 2 Screws: M2*10mm - 1 Nut: M3 - 2 Nuts: M2
thingiverse
A custom 40mm fan duct designed specifically for the Anet ET4, engineered to fit snugly within the metal fan housing and significantly enhance cooling performance of the heat sink, addressing apparent heat creep concerns that arose in previous...
thingiverse
Find more upgrades for ET4 printer: 1/ Y Belt back holder reinforcement: https://www.thingiverse.com/thing:4166801 2/ Y Belt Tensioner: https://www.thingiverse.com/thing:4166953 3/ Universal spool holder ET4 adapter:...
prusaprinters
You just need 2 x M3 bolts and nuts. Print instructionsCategory: 3D Printer Parts Summary Modified the original Thing to suit the Labists ET4. The bed on the Labists ET4 has the wires soldered direct to the heated bed but the cable management is...
thingiverse
Remix of awtilso's A8 electronics enclosure, I cut the parts in half to make them printable on smaller print areas. ...Print Settings Printer Anet A8 Rafts No Supports No Resolution 0.2mm Infill 20%
thingiverse
Extra help to level the bed with dial gauge in labists et4 or any printer with this extruder.
cults3d
The bed on the Labists ET4 has the wires soldered direct to the heated bed but the cable management is rubbish and likes to wrap around the Y endstop. This replaces everything at the bed and directs the wire to the side. ...You just need 2 x M3 bolts...
thingiverse
The bed on the Labists ET4 has the wires soldered direct to the heated bed but the cable management is rubbish and likes to wrap around the Y endstop. This replaces everything at the bed and directs the wire to the side. ...You just need 2 x M3 bolts...
thingiverse
Also printed are: - 4 corners consist of 2 parts each - 4 feet - 2 frames for the original frame consist of an upper part, a lower part and a shell for 806Z ball bearings (optional) - 2 T-pieces for the cross brace - 2 brackets with 30 ° rotation for...
thingiverse
I demonstrate the installation on a ANET ET5X printer and have designed a bunch of custom parts that you may or may not need for your application. You can find those parts here: ► YOU ARE HERE Print the main fan shroud with the 40mm extruder fan...
thingiverse
This project began as a concept to create one solid main frame for Anet A8 to replace the two loose stock frame parts, but during the verification process I realized it would be much better to design all printer components. Apart from the obvious...
thingiverse
I've modified the fan duct with slightly wider holes to fit seamlessly with the Anet A8 E3D V6 Bowden MODULAR X Carriage V4. ...The original design was colliding with my BL Touch sensor, but this revised version gives me a bit more clearance to move the...
thingiverse
I had a dual extruder from anet, I didn't need a 3: 1 conversion, So I made the foundation and used some parts, Screws as needed, 1x Nut 5x2.5, https://youtu.be/th8ruoFTwDI The advantage is dual drive, Controllable pressure, Less space for filament...
thingiverse
For the default Upper part, a file called Anet part for Default upper part.STL has been used. == Anet A4 Part == - The Rod Holder design has been improved by deleting the plastic bushing. - A hole for nuts has been added to make assembly easier. -...