anet et4 extruder 3d models

I designed a Bowden Mount Extruder specifically for the TATARA frame, featuring a sturdy bracket that securely holds the extruder's stepper motor in place. ...The motor is easily removable, allowing for effortless maintenance or replacement as needed.

I'm a helpful assistant screw that propels the filament smoothly into the extruder. ...Typically, whenever I switch filaments, threading them through the extruder usually gets hindered by the tube connector.

Standard issue A8 branded extruder control module, commonly referred to as a precision-machined rotating dial or knob.

You'll be able to install your stepper motor for the extruder onto the X-axis using this mounting bracket.

I crafted this revised version of the extruder LED light, showcasing my mastery of Fusion 360's capabilities.

I revised the upper section of the extruder motor, requiring a switch to the opposite side. ...The job is complete!

This video provides a visual examination of the filament feed system's functionality, specifically its connection to the extruder.

... be updating it soon. The design can accommodate either two extruders and another component or three extruders altogether. ...Edit: The thing broke off when I was adjusting it, so I came up with a revised version that supports two fixed extruders.

I was determined to secure the incredible Gavtech Extruder to my AM8 printer, so I devised a solution. To achieve this, you'll need to follow these steps: 1. Locate the mounting holes on the Gavtech Extruder and your AM8 printer. 2. Drill pilot...

***~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~*** This modification involves cutting down the extruder heatsink. In my opinion, the increased airflow more than makes up for this, allowing the extruder to run at least as cool as it does...

... to illuminate the printing area. ...The component is designed with a 45º angle taking Z or Y axis as reference to try to maximize the amount of light around the nozzle. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20%

Adjusted to accommodate larger top bolts on the Anet A8 plus printer. Update: Created a refined version of the design. It offers four screw holes specifically designed for NEMA 17 motors. ...This revised plan assumes a 20mm spacing for mounting bolts...

I Designed this shroud to fit perfectly onto the Anet A8 Fan Hinge V2, created by the talented AShifter on Thingiverse at https://www.thingiverse.com/thing:2696721. This upgrade simplifies the look and expertly directs cool air exactly where it's...

... filament guide out of 4mm teflon tube. ... This device is compatible with the standard Anet A8 carriage. ... Please be aware that you will need to use slightly longer M4 screws, because the stock ones are too short to reach the bearing housing's hole.

Thanks Pierrelesek for sharing a brilliant support extruder design on Thingiverse, specifically the L3K model found at http://www.thingiverse.com/thing:512338.

I'm looking to add an M4 screw holder for my extruder fan mod, and I need a 10mm long screw for the job.

This modified design works with both Anet A6 and Anet A8 printers, but it currently supports only 40mm fans. ... To build this, simply print two units and follow the instructions found on the original project page, which also includes fan protection.

I upgraded my old ANET A6 to a CUBIC Printer, just like this one: https://www.thingiverse.com/thing:2067818. To make this transformation, I utilized the Frankenstein mod: https://www.thingiverse.com/thing:1692794. Since I couldn't find an adequate...

A Simple Assembly for a Bed Leveling Comparator.\r\n\r\nDesigned with FreeCad 0.16 and Sliced via CURA 3.2.1.\r\n\r\nPrinted on an Anet A8.\r\n\r\nUsage of Support is Strictly Required.\r\n\r\nFeel free to Modify and Enhance this Design!\r\n\r\n***...

I also decided to give it a shot on my A8, as the first bowden extruder I used with it (converted from the original direct extruder) had problems gripping some filaments and the geared extruder I tested with it (originally built for a Hypercube...

Allthough the extruder/fan/nozzle cables on my A8 are attached with cable ties, there is some movement in the extruder plug while printing. With this strain relief the cables stay in one place. Use a cable tie to connect. ... NB: This is version 2, I...

I printed out and put through the paces about a dozen different carriages and mounts for Bowden extruders with BL touch sensor attachments before deciding to create my own from scratch. This was my first-ever DIY attempt, using the following carriage...

... assistant screw that helps the filament go through to the extruder. ...Most of the time when I change filament, and I tried to thread the filament through the extruder it bumps into tube connector. ... UPDATE (01/02/2019): Dimensioning problem solved.

This support provides easy access to the extruder, making it simple for users to swap out filament whenever needed. ...The design is based on the original LeoN model found at Thingiverse, with a straightforward modification aimed at enhancing usability.

This is an adjustable riser block used to elevate the extruder motor away from the base of a enclosed build platform, providing easy access to the Bowden tube and connection point for the hotend assembly.

I recently updated a design by Brogz007, specifically his Extruder Mount model 2146021 on Thingiverse. This design is a great example of simplicity done right. ...I added some extra reinforcement to the sides, giving it an extra layer of stability.

Frustrated with the hassle of grasping the extruder feed wheel spring, I designed this cap to encase the screw. ...Its 7mm interior hole makes it potentially useful for others as well.

A makeshift fix for my crippled extruder fan, I'm using an adapter that lets me slap an 80mm fan onto the shell of the old one. ...It's no ideal solution, but it gets the job done.

Here's a simple clip-on motor mount designed specifically for Bowden setup applications. ...I've created two versions, one for the left and another for the right-handed extruder variants.

Features: The best thing about this setup is that you can adjust the extruder height easily while printing with just one screw, allowing you to keep the hotbed in a fixed position without needing an extruder sensor. Extruder trays enable quick...