anet et4 extruder 3d models

Perfectly fitting smoke detector: Ei650 You will need: 2 x Screws for attaching the smoke detector. ... Remix from: Cable Clip: https://www.thingiverse.com/thing:2731180

This is a modified Version of the X-Belt Tensioner designed from “Misterguru” on thingiverse.The edge of the base body, which is in contact with the sheet metal, was moved by 20.3mm. ...In addition, an additional edge has been added to the base body at...

Upgrade your Anet A6's 40mm Fan Bracket with this superior design, proven to outperform the original. ...Check it out on Thingiverse at https://www.thingiverse.com/thing:3100700.

This is a trial run for a dual extrusion mount designed specifically for the Anet A8. ...If anyone happens to print this prior to my test, kindly report back any adjustments that need to be made.

Tired of hurting your fingers and having to display extreme feats of strength when unloading filament from the Anet A6? ... This mod allows you to get more leverage and more area to press.

Print Settings Printer: Anet A6 Raft Settings: No rafts are required for this print. Support Settings: Supports are not necessary for this design. Resolution Settings: The resolution is set at 0.08 mm. ... Infill Settings: A 20% infill...

A sleek LED ring perfectly complements the extruder, seamlessly integrating with the original cooler's design.

Direct Extruder for my ET5.It works great, easy to install.

A remarkably lifelike replica of Anycubic's extruder lever, requiring minimal force to operate smoothly.

This is a versatile Cage designed specifically to securely hold a Bowden Extruder in place.

Filament Guide for Anet A8 3D Printer Installation and Usage Instructions The filament guide is a crucial component of your Anet A8 3D printer, ensuring smooth and efficient printing operations. It plays a significant role in maintaining the correct...

This design is specifically intended for supporting a single LED strip that will be attached directly onto an extruder carriage.

I've modified this piece https://www.thingiverse.com/thing:2408447 to fit the Anet A6 as the holes for screws didn't line up along with several other tweaks, you'll need to swap out the original screws for some M3-30s.

...This design was inspired by the dryas cool button found on Thingiverse (http://www.thingiverse.com/thing:1935151). Print Settings Printer Anet A8 Rafts No Supports Yes Resolution 0.1 Infill 20% Notes Only a small support was used for the central pin.

YouTube: Silas Pfeifer Print Settings Printer: Anet A8 Rafts: Yes, enabled for smooth start-ups. Supports: Yes, to prevent warping and ensure stability. Resolution: Adjustable from 0.1-0.2 millimeters for precise prints. ...Infill: Set at 100% density...

Here is the rewritten text: Print Settings Printer: Anet A8 Rafts: No Supports: No Infill: 100% Solid Print a dry-as-button remix of the original design, but swap out the button shaft for a sleek hexagonal one to eliminate rattling issues.

... by a cool button on Thingiverse, specifically dryas's button at http://www.thingiverse.com/thing:1935151. Print Settings: Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.1 Infill: 20% Notes: Minimal support was used for the central pin only.

Just a remix to hold the bed level sensor so you can install a micro swiss direct drive all metal hot end on an ET4 pro. ...This does require a slimmer stepper motor for the extruder.

simple extruder mount for the A8. ...i didn't like the position of all the other ones, this one works great.

A breakthrough 3D printer carriage designed to perfectly accommodate dual extruders sourced directly from Ali-Express! ... ***ALPHA RELEASE - EXPECTATION OF CONTINUED DEVELOPMENT!!!***

... heatsink's fins and allows the fan to be positioned directly above them with a small clearance. In my opinion, this is an improved solution. Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 100%

Small fan duct upgrade for your Anet A8 printer \nWith this modification, you'll enjoy clearer visibility of the first layers as they print. ...\nFor optimal results, use a 0.2 layer height and 40mm/s printing speed.\nNote: ABS is highly recommended for...

... and allows the fan to point straight into the fins with a little space. I think this is a better solution. Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 100 Category: 3D Printer Accessories

... setup. ...This particular configuration is hands-down the most effective way to attach it. Not only does it offer precise alignment, but it also creates a clear pathway for filament feed and cable management within easy reach of the extruder itself.

Button to feed filament to the extruder or to remove it. Model v3. ... Feel free to share, like my creations and especially share your makes of them, it helps a lot.

This update grants unrestricted access to the extruder motor. Changing filaments has never been easier. Installation is straightforward, taking mere minutes to complete. ...Appreciation goes out to Thingiverse for making this design available at...

I built a straightforward extruder mount for my A8. ...I found the positioning on all other mounts to be off-putting, so I designed this one with functionality in mind and it's been working flawlessly.

So I designed this to get better access to the extruder:\r\n\r\nhttps://www.thingiverse.com/thing:2551414\r\n\r\nBut you can't attach it directly to the extruder with any of the leftover hardware (or with any of the various M3 screws I purchased). ... I...

Original Extruder Top Block Designed Specifically for the A8 Screw System. ... The New Part Includes a Crucial 5mm Thread that Enables Seamless Integration of a Pneumatic Coupler on the Filament Side.

Printing with ABS or PET-G materials often results in high temperatures, which is detrimental to the extruder motor's performance. As it stands, this vital component operates in an extremely hot environment, leading to subpar functionality. If your...