anet et4 extruder 3d models

I wasn't satisfied with the extruder button I was using on my Anet A8 so I decided to create a new one that would work perfectly into place. This design fits seamlessly into the A8 extruder, utilizing the same original screw and nut that comes...

Printed Parts: 1) A8 Dual Extruder - V3.3 Carriage Mounting (Note: This part may require PETG) 2) A8 Dual Extruder - V3 Part Cooling Duct 1) A8 Dual Extruder - V3.3 Top Left 1) A8 Dual Extruder - V3.3 Top Right Optional Parts: 1)...

Printed Parts 1) A8 Dual Extruder - V3.3 Carriage Mounting (This part may need to be PETG) 2) A8 Dual Extruder - V3 Part Cooling Duct 1) A8 Dual Extruder - V3.3 Top Left 1) A8 Dual Extruder - V3.3 Top Right Optional Parts 1) X_Axis_Cable_Tray_Mount -...

I was not satisfied with the extruder button I was using on my Anet A8 and decided to create a new one. This design fits perfectly into the A8 extruder using the same original screw and nut that comes with the printer. It is more comfortable to the...

Physically screw mount a fan onto the anet.

Print Settings: Printer: Anet A6 Rafts: Yes Supports: Yes Resolution: 0.4mm, 0.2mm/layer height Infill: 10-15% Notes: Material is PLA, 175mm Working Temperatures: Extruder 210°C, Heated Bed: 55°C Using Cura 15 with rafting and support, it will take...

Additionally, I use the Anet A8 Extruder Fan Spacer by AZDawg (http://www.thingiverse.com/thing:1798669), which I customized so the fan sits flush on the aluminum block. Both parts are screwed together with one 3x40mm screw and two 3mm nuts. The...

Carriage to mount an E3D extruder and a BLtouch level controller on an Anet A6 printer...

Printing TPU or flexible filaments with the Anet E10 extruder can be a small challenge, especially when it comes to avoiding over-tightening and potential print complications. To address this issue, several updates have been made. Version v2 brings...

I designed this extruder from scratch based on the Anet A6 Extruder Prototype Bowden & Direct by Bomber0 \r\n\r\nhttps://www.thingiverse.com/thing:2338084 \r\n\r\nInitially, I used most of the original dimensions, but eventually created my own...

Extruder fan silencer mod, bolt on top of your 50mm radial fan to bring down DB. On my setup from 30cm away Without Silencer: 65DB With Silencer: 57DB Bolt mounts are wide enough for M4 and are 2mm thick. Print to the quality you require, print is...

So I made this to get better access to the extruder: https://www.thingiverse.com/thing:2551414 However, you can't mount it against the extruder with any of the leftover hardware (or with any of the assortment of M3 screws I bought). Everything's...

With this setup, you can change filament without removing the fan - the space between the extruder shaft and the fan is wide enough to easily see the hole for the filament.\r\n\r\nI hope you enjoy my designs. If you have ideas on how to improve them...

this thing adds an aluminium heatsink and moves extruder stock heatsink and fan 23mm far and 20mm right from extruder motor allowing for visual inspection of the extruder, it maintains or even improve heatsink funcionality by expanding its total...

This is a Extruder Cage to mount a Bowden Extruder.

Extruder brace to stiffen and straighten extruder bracket

This mount is designed specifically for use with the "Compact Bowden Extruder, direct drive 1.75mm" by Schlotzz, available at http://www.thingiverse.com/thing:275593, on Anet A8 Prusa i3 clone printers. It may also be compatible with other printers...

This is a filament guide and vent fan holder for the Anet A8.

### Highlights: - optimized for perfect balance with motor as close to smooth rods as possible to minimize play - rigid but lightweight, high stress parts are one piece - open assembly for easy servicing - you can use HOT2 fan duct from original...

The Anet A6 Extruder Fan Upgrade Kit is a must-have for improving your 3D printing experience. It comes with several essential components to enhance filament handling and cooling efficiency. The kit includes a cap for the extruder filament screw,...

The Anet A8's extruder fan modification is a straightforward upgrade that enhances print quality and reduces noise levels. This DIY project involves replacing the existing fan with a more efficient one, typically a 40mm or 50mm model. The new fan is...

I had already cut the heat sink, leaving the bottom five ribs mounted to the extruder frame in place. This took care of helping keep the heat away from the filament, but I knew I should have more airflow. I checked the heat load routinely with a...

I designed this Thing to make it easy to access the extruder of the Anet a8 Printer when it gets jammed. Changing filament is also super easy, because you can actually see if the material fits the hole. You will need: -1x M4 metric screw (min 20mm)...

This is mount for E3D bowden extruder with extruder motor on top which makes it more like direct extruder.

This repositioned extruder fan enables better troubleshooting and often resolves filament-related issues without requiring a complete disassembly of the extruder. ... For more information or to explore other related designs, please visit my collection...

Inserting filament through the Anet extruder into the nozzle throat can be quite challenging due to open space beside the right filament track in the extruder design. This issue is particularly frustrating when working with bended or flexible...

This was created to replace the 9-blade "muffin" fan on my Anet A8 extruder. The stock fan is weak, and unfortunately, if you have the same problem I did and break a blade, the fan becomes VERY noisy and vibrates excessively (affecting print...

A Custom Extruder Filament Guide with Enhanced Screw Engagement.

Hopefully this will be the last update. Wanted a new extruder for my A8, Still learning how to use fusion 360, so thought a good place to start would be to mix up a few files and see where i end up. A couple of the parts ive uploaded twice, there is...

A custom x-carriage designed specifically for the Anet A8 MK8 Extruder with its stock 37mm long stepper motor. This carriage has mounts for Igus RJ4JP-01-08 bearings, but any 15mm diameter, 25mm long bearings with locking notches will fit perfectly.