anet a8 y tensioner 3d models

The Y bar stopper designed for the P3STEEL 3D printer utilizes stock smooth rods measuring 380mm in length, sourced directly from the Anet A8. To enhance stability, I've added a washer to the design. ...My PRUSA I3 STEEL frame was printed by Orballo...

I tore apart my Anet A8 printer according to the instructions found at https://www.thingiverse.com/thing:3401790, a project that really sparked my creativity. ...After completing the rebuild, I discovered that the Y motor mount was woefully inadequate...

Anet A6 or A8 Frame Secure Clamp for Y axis For reinforcement for y axis and tighten on board Print Settings Printer: Anet A6 Evolution Cube Rafts: Doesn't MatterSupports: Yes Resolution: 0,3Infill: 20% Category: 3D Printer Parts

This is a riser for the Y carriage from RepRapChampion: http://bit.ly/2oBznGf On some printers, specifically the Anet A8, the carriage sets too low and hits the Y axis motor without a riser, so this one provides just enough clearance to avoid that...

This is a remix of Simhopp's belt_y_3.skp from thing:1433295 specifically designed for the Anet A8-B printer with an aluminum three-part heated bed stand and a 12 x 20 mm screw hole distance. Choose the STL that best fits your printer's heated bed...

Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.3 Notes: You can print these parts at a layer height of 0.3 mm or higher, and crank up the speed - precision isn't crucial here. However, assembling the chain can be a bit tricky...

For those who have correctly assembled their bed plate holder by deviating from the standard Anet A8 assembly instructions, this device may not be suitable as the belt height would already be in alignment with the pulleys. Key benefits of this...

Double Smoother Mount for Anet A6 and A8. This mount replaces two spacers on the mainboard. ...Check out my other Anet A6 parts at: https://www.thingiverse.com/andreas_g/collections/my-a6-parts

These prints represent my attempt at enhancing some of the already outstanding Anet A8 parts available on Thingiverse. Previous braces have some features that make it challenging or impossible to install several belt tensioner upgrades. Take a look...

To do this I redesigned the Prusa i3 bearing mount (https://www.thingiverse.com/thing:710913) and Y-belt attachment (https://www.thingiverse.com/thing:587659) to fit for Anet A8. You will also need some M3 nuts and bolts. Note: after this upgrade...

This is a two-piece reinforcement bracket specifically designed for the Z-stepper motors on the Anet A8 printer. It's part of a comprehensive set of printable reinforcements that have not yet been published. The lower section, highlighted in red,...

Anet A8 Y-Axis Cable Chain Work&Force&Weight Optimized I obtained the components from "papinist" at Thingiverse (https://www.thingiverse.com/thing:1915486). Issues: Following the Printout - I discovered that the chain holder at the hotbed has...

... Fits an Anet A6 or A8 Printer or Other Printers with a 220x220mm Holder. There Are Two Different Versions Available: One with a 1mm Thickness and Another with a 3mm Thickness. Special Thanks to FedeMiller for Providing the Various File Formats.

Double Smoother mount for Anet A6 and A8. Mount Replaces two spacers of the mainboard. ...and take a look at my other Anet A6 parts: https://www.thingiverse.com/andreas-giesert/collections/my-anet-a6-parts Print Settings Infill: 100% Category: 3D...

I modified the original design because the fork's strength issue required an adjustment. ...I also reduced the hole dimension to fit the nut snugly, as it was spinning with the bolt.

You'll require two additional m4x35 (or extended) bolts and two m4 nuts on top of what's already listed.

This creation was brought to life with the innovative tools of Tinkercad. ...To make your own adjustments, simply visit https://www.tinkercad.com/things/3gjF6s4KXpL

I tried SUPASORN's design twice, but it snapped one leg the moment I applied some pressure. Perhaps my 3D printer has faulty ABS, that's a possibility. ...To fix the issue, I simply added a little extra material on either side, and it held up just fine.

The revised design boasts posts that are precisely proportioned and slightly thicker than its opening counterpart. This adjustment ensures a seamless fit, while the elongated posts guarantee continued stability as they're drawn towards the wider end...

Mounting points reworked. ... Fits for the slim belt.

To complete this task effectively, gather two additional M4 x 3/8" machine screws or longer and two M4 locknuts.

I reinforced the frame to withstand heavy loads and prevent cracking over time. ...I upgraded the threading system to offer smoother, more precise adjustments.

I reimagined it to fit my needs perfectly. The bolt holes are now tailored specifically for M4! I also widened the central space to accommodate a pulley seamlessly. I've sent the original design to Freemark. Thanks, and happy building! ...Thing 1683070,...

Rods in my printer are experiencing some play due to slackness. ...A straightforward solution is to use this adjustable stabilizer to secure them firmly in place.

This is a 2-piece Y-axis belt holder for the Anet A8! If you've upgraded your belts to fiberglass, check out my other items - I have one designed specifically for that upgrade, although this design works with both belt types. Make sure your H-frame...

The y-axis motor mount is a crucial component of the Anet A8 3D printer's frame structure, designed to securely hold the y-axis motors in place while allowing for smooth and precise movement along the y-axis. This essential part ensures that the...

It's a custom build combining the Y-axis redesign for Anet A8 with a frame reinforcement designed specifically for 8mm rods. I've been using this setup for over a year now, and it's essential to note that some thermal insulation is required between...

Simple chain hold down for Glass bed users on Anet A8. Requires drilling two small 3mm holes in H-Frame under glass, or simply glue it down - your choice. This little bracket keeps Y axis chain held down when the bed is at its back travel,...

My ANET A8 had been delivered with a defective LM8UU linear bearing. it had a lot of friction, was very noisy and eventually lost 2 balls I found on the floor... Moreover, the design of the Y axis is somewhat overconstrained with 4 linear bearings...

My Anet A8 arrived with a defective LM8UU linear bearing. The bearing had excessive friction, was extremely noisy, and ultimately lost two balls that I found on the floor. Furthermore, the design of the Y-axis is somewhat overconstrained due to four...