anet a8 y axis upgrade 3d models

Endpoint upgrade Anet et5x

Improved Y Axis for 3030 Alu Extrusion Frames. ...Provides rigid Y belt anchoring and low profile for rods attachment to avoid collisions with bed levelling screws.Increase height of the Y carriage from the bearings (washers or longer M4 screws with an...

I modified the Carriage_mount from juh's design for the Anet_A8_lightweight_and_unobtrusive_X-axis_cable_chain to fit seamlessly with Don1337's E3DV6_BasePlate from the Anet_A8_E3D_V6_Bowden_MODULAR_X_Carriage_V4_BEST_ONE. The original part needed...

... extruder and the new ALU version. ...These extruder components also support iamjonlawrence's Y axis upgrade, while Part E1 from http://www.thingiverse.com/thing:193668 adds a 30mm fan for cooling. ...Stay tuned for a custom bottom plate release soon.

My Anet A8 use plastic bearing block holder and the bed leveler screw interference with the rod/endstop holder so I shorten the holder a bit and also make a bearing block spacer to slightly lift the printbed.

Compact Cooling Fan Upgrade Kit for Anet A8 3D Printer.

The y axis required the use of a smaller wheel to allow for the complete motion of the carriage with the installation of the 42-40 stepper motor. The y axis motor is running at 37c and the prints have a better surface finish. I have include the...

I created an upgraded X-axis tensioner for my Anet A8 printer using FreeCAD (blueprint attached). It provides a snugger fit, allowing me to utilize a 16-tooth idler bearing with an M3 screw. To install the tensioner, I need two M4 screws and nuts,...

USE THE VERSION 2 LINK:https://www.printables.com/model/324899-ender-2-pro-y-axis-linear-rail-upgrade-v20THE v1.0 VERSION IS NOW OUTDATED.This idea came to me when I had to change the wheels on my Y-Axis carriage. It was a total pain in the...

The Y belt attachment is designed specifically for the Anet A8-B printer (the one with an aluminum 3-part heat bed stand and 12 x 20 mm screw hole distance). Choose the STL that best fits your printer's heated bed stand configuration. If the...

The 20x12mm bolt pattern fits my newer Anet A8 y-carriage (circa January 2018). Be aware that depending on how you initially assembled your y carriage, this may not fit without some reassembly work... the attached file is for 6mm carriage spacing...

These files match the original X-axis belt tensioner found in the Anet A8 Plus kit, but I encountered problems with the belt slipping out occasionally on my end so I decided to upgrade the smaller component of the belt holder allowing you to loop the...

This upgrade enhances y-axis stability significantly and simplifies bed leveling due to having only one rail. The original 'frog' had a cutout for drilling holes, allowing just two hole placements. A take-up piece is used with penny washers for...

Needed materials, just like the original design: - 2x M5 bolt (length varies per machine) - 2x M5 nut - M4 bolt (< 50mm) - M4 nut - Original Anet A8 M3 bolt (18mm) - Original Anet A8 M3 nut NOTE: In the pictures, it looks like the block part is...

Print Settings Printer: Anet A2 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2 Infill: 100% Notes: I printed mine in PLA with 100% infill. Motor mount should be printed upside down, no need for supports. The stabilizer can be printed...

In addition to the X axis modifications, I designed the bed carriage, mounting elements, sensor support, sensor extension arm, and Y belt holder for the Y axis. The Y belt holder was also printed with 100% infill. To prevent oil from seeping into...

Oldham Z-Axis Coupler/Coupling (three-piece, all-in-one print) supersedes standard flex couplings entirely. Two distinct versions are readily available in the files, allowing either a single combined print or separate prints for each piece, catering...

You can now mount the plate and test print with the extended x-axis print area, even though you cannot use the full y axis yet. Next, use the 4 inch y axis extension to extend the y axis to 10 inches. Use manual control movements to verify the final...

To Prevent Excessive Height Buildup and Extruder Impact, Utilize Thing 1915486's Enhanced Cable Chain Design Specifically Designed for Anet A8 Y-Axis Operation.

The X-axis of the Anet A8 3D printer has been switched from a belt to a screw. Firmware has been updated to skynet3d version 2.3.2. Since there were no YouTube videos available, I connected my Korean Naver blog instead. ... Check out the video here:...

An innovative solution is required to accommodate a thicker (1.7mm) GT2 belt on the Anet A8 X-Axis belt holder. To achieve this, several essential components must be sourced. ... A crucial item necessary for assembly is an M3 x 18mm allen screw, which...

I was searching for some z-axis anti-wobble top plates for my Anet A8 printer that wouldn't look unusual. Since I couldn't find one, I decided to design and build my own. ... If you want a more secure mounting option for your bearings, check out this...

This is a customized remake of alexsomesan's Anet A8 Brackets to Minimize X-Axis Movement, specifically tailored for Bowden setup. The original design can be found at https://www.thingiverse.com/thing:2056563. ...I had been looking for one that could...

... while the smaller one is an evolution of redangel1984's V3 model. Both are specifically engineered to work seamlessly with the Anet A6/A8 printers, ensuring precise adjustments when calibrating the Z-end stop thanks to Bomber0's clever modification.

Any feedback is more than appreciated on where I can improve. This set is designed for a Thinker S V2.0 with a linear rail upgrade on the X and Y axis. The chain for the Y axis will ONLY work if the bed is on linear rails, it needs the extra...

Improve Y-axis belt tension with this printable upgrade. This design features a screw for adjusting Y-axis belt/pulley tension by turning it. Find the X-axis belt tensioner here: http://www.thingiverse.com/thing:1673. Versions V1 to V6 were...

This is a remix of the Y-axis idler mount for a Bear upgraded Prusa MK2.5 to make it compatible with the Gates idlers sold by E3D. I adapted my modification from the changes *motocoder* made to his remix of the MK3 version to accommodate the same...

... The main frame is done, I still have to create the Y-axis belt attachments for the carriage. I'm not trying to build an original prusa mk2. Just customizing it as I go. It's still a work in progress, will upload more files once they are done.

This is a Y-Axis upgrade for the Folgertech Prusa i3 2020 Variant, but it should work on any 2020 rail printer and can be adapted to an all-thread framed printer with some additional parts. It replaces cheap linear bearings and 8mm rods with an...

A Modified Belt Tensioner for Anet A8 Printers. I'm a huge fan of MrPaulM's original design, but I had one major gripe - the big screw-bolt. So, I decided to give it a complete overhaul and redesign the front plate to accommodate either M4 or M5...