anet a8 y axis upgrade 3d models

I upgraded my baseplate to the Rep Rap Champion base plate so I remixed the chain clip to latch on to the new baseplate. Photos to come once I have the chain printed and attached. ...I also remixed the end plate that attaches with two screws so it...

As part of my ongoing mission to upgrade my A8 Plus piece by piece, I decided to swap out the somewhat subpar X axis idler with a toothed version. This adapter makes it possible to install a 16T idler. It attaches to the outside of the right Z axis...

... together and implement a stepper screws raiser plate too. #TESTING: I'll be testing and reporting effects of each upgrade in my review of this frame at http://mirko.vukusic.net/3d%20printing/anet-a8-tatara-steel-frame-by-orballo-printing-review/.

To ensure optimal prints without blobs all over the inside, set the following Cura Print options: - Layer Height: 0.27 - Combing Mode: All - Retraction Min Travel: 5mm - Print Speed: 30mm/s - Cooling: 5% (assuming you're using a Titan Aero design) -...

This bracket is designed for easy z-level adjustment of the Anet A8 (or any other printer with 8mm guiding rails) 70mm length should be the right height to place it under the y-z level joints right after doing the auto home. then you can manually...

I'm remixing an anti-wobble design specifically for the stock parts of my Anet A8. ...The best part is that I won't have to disassemble the entire printer - just a few screws will do the trick.

I designed this specifically to accommodate the sensor on the right front side when facing it directly.\r\nIt's tailored for the standard Extruder used in the Anet A8, ensuring a stable setup overall.

This is a modification of the Anet A8 printer frames to synchronize the two z-Axis motors. This update builds upon the Anet A8 Z Redux - Synchronized Motors design by uanCarlos_3design, available on Thingiverse under...

Original Source: https://www.thingiverse.com/thing:3213207 I've used above belt tension system on my printer(Anet a8), which has A8 mainboard V1.7. Two things have been modified. - Puller became slimmer to fit well with a supporter frame. -...

This is an X Axis Leadscrew and E3D V6 conversion for the popular Anet A8 3D Printer... The plan is to run a bearing supported leadscrew with the X axis motor end mounted on the Left. The main carriage is significantly smaller and should be...

Adjustable induction switch mount Model: LJ12A3-4-Z / BX (diameter 12) Z axis, for Anet A8 Printed standing up, Petg plastic, props only from the table. After printing, you need to work with Hands. Hole 1 - We drill with a 3.5 drill and cut the M4...

Universal x-axis carriage (three bearings) upgraded on 12/10/2018 to accommodate larger M3 nut spacing requirements.

... be. Update: Failed clamping holds enough Added breakout wall for printing, plastic sag Anet A8 protection against lateral vibrations on axis X Protection at the distance between side walls - 294mm Used four aluminum profiles of 14x14mm by 250mm.

Horizontal X-axis for Anet A8 and more that improve print quality and print speeds. I'm currently running the printer at 95mm/s with a X-acceleration at 5000mm/s (in the printer, so it's real), 400mm/s travel speed (with 6000mm/s acceleration in...

Horizontal X-axis for Anet A8 and Beyond to Enhance Print Quality and Speed. I'm currently operating the printer at 95mm/s with a X-acceleration of 5000mm/s, set in the printer itself, reaching 400mm/s travel speed with 6000mm/s acceleration during...

These brackets are designed for the first series of Anet A8 printers to minimize X-axis motion particularly when printing in higher levels of the printer.\nTo attach the brackets you will need to disassemble the display screen and remove the four...

This remix adjusts https://www.thingiverse.com/thing:1959208 to ensure the height matches that of the Y axis motor pulley when a 20-toothed toothed idler is used. Toothed idlers reduce belt wear and supposedly minimize vibration compared to smooth...

This project creates an adjustable probe mount for the SN-04N or PL-08N capacitive sensor used in Auto Bed Levelling on the Anet A8. There are two versions of the probe mount, depending on your extruder heat sink and fan configuration (either "out...

Humans operate at a pace of 0.3 layers per minute, with printing speeds reaching up to 80 millimeters per second and an infill density of 30%.

The belt tensioner consistently malfunctioned. ... I addressed the issue by resolving its recurring failure.

This is a work in progress that will be updated frequently. Please carefully read all instructions before proceeding. The instructional pictures I have created are listed below, so feel free to leave a comment if you have any questions. Things to...

This is a custom-made toothed pulley and belt adjuster for my personal 3D printer project. The pulley utilizes the stock bearings provided with the printer, resulting in smoother operation due to its toothed design which reduces noise levels. ...I drew...

Click this link to view the comprehensive video guide at https://www.youtube.com/watch?v=RXOOciINaNE.

... adjustments to the mounting position or sensor orientation to achieve optimal performance. By following these simple steps, you can effectively install a bed level sensor on your Anet A8 3D printer and enjoy more precise prints with less hassle.

Hey everyone, I've got a simple fix for The Anet A8 printer that's going to resolve the annoying Z-wobble issue plaguing this affordable printer. All you need to do is print out this part and attach it to the threaded rod on top without taking...

This is a X-axis tensioner designed specifically for the Anet A3 that boasts an expansive opening suitable for accommodating the toothed 16T idler commonly sourced from online marketplaces such as eBay and Aliexpress.

Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.80 Infill: 100% Notes: You probably don't need 100% infill, but this small part has a lot of tension on it. It took about two hours to print at these settings. A higher...

Adjustable induction switch mount Model: LJ12A3-4-Z / BX (diameter 12) Z axis, for Anet A8 Printed standing up, Petg plastic, props only from the table. After printing, you need to work with Hands. Hole 1 - We drill with a 3.5 drill and cut the M4...

Knob for the upgraded A8 Anet display.

It features TTL output, ensuring seamless integration with Anet A8 devices. ...To get started, simply connect the pins correctly: the left pin of the motherboard connector serves as Ground (GND), the middle pin provides Voltage (VCC), and the right pin...