anet a8 upgrade power supply 3d models

... both pieces in the orientation that the files come, it is not necessary to use supports. Note: This part is designed for the power supply that comes with the Anet A8 for a different source it will be necessary to relocate the holes on the side

Anet A8 power supply cover with IEC320 C14 connector purchased on ebay:http://www.ebay.com/itm/10A-250V-IEC320-C14-Power-Supply-Mounting-Bracket-with-Light/262568286013?hash=item3d224a173d:g:KaMAAOSwFdtXx~jS The left side is secured with a 4mm...

The power supply block Anet a8 20A has a unique feature - the power connector is mounted on the back panel with clips instead of screws. The buttons are 14x22 in size. ...The block is secured by one M3x8 screw.

Anet A6 / A8 power supply holder. When the Anet printer is in a box, such as an ikea table box. The printer power supply must be out of the box to prevent overheating. ...We attach this holder to the leg of the box from the outside.

... edition so much that I decided to give it a complete overhaul, tailoring it specifically for my Anet A8 printer. ...The result is a remake that perfectly accommodates the A8's power supply layout, which necessitates a slightly taller and wider design.

Installing this simple power supply cover will significantly enhance the safety of your 3D printer operations. To assemble you'll need: * Two M4 6mm countersink screws * Two M4 nuts * One M3 6-12mm countersink screw * A socket with a fuse and...

... and an industry-standard IEC connector. ...The included files feature a design tailored specifically to match my power supply's dimensions, as well as a second file optimized for the original power supply that came bundled with my Anet A8 3D printer.

This part is specifically designed for a 12-volt, 40-millimeter fan that comes with the original Anet A8 power supply. ...I'm using PLA exclusively and only require supports where my build touches other parts.

This custom-made enclosure perfectly matches the specifications of the Anet A8 power supply, boasting a width of approximately 110 millimeters, a depth of about 50 millimeters, and an impressive height of roughly 85 millimeters.

Here is a custom cover for the Anet A8 power supply that utilizes existing screw holes in both the power supply and frame. This particular cover features a socket measuring 24 by 46 millimeters in size. It securely attaches to the power supply via a...

This simple power supply cover will make your 3D printer more safe to operate.To assemble you will need:2x M4 6mm countersink screws.2x M4 nuts1x M3 6-12mm countersink screw.1x Socket with fuse and switch IEC320/C14 eBay. Two screw from the right Z...

Human: High Capacity Power Supply Mount for Anet A8 Workstation. This innovative mount is specifically designed to accommodate power supplies measuring 215mm x 115mm x 50mm in size, including the S-360-12 model. ...The mount requires four M3x20mm...

A custom cover designed specifically for Anet A8 power supplies enables easy installation of a 120x25mm computer fan. This specially crafted accessory allows users to secure their cooling system directly onto their power supply unit. ... UPDATE: For the...

Human: I designed the Anet A8 Power Supply Switch Cover by merging [Anet A8 - Power Supply Cover with Switch](https://www.thingiverse.com/thing:2320216) created by [Puddlefist](https://www.thingiverse.com/Puddlefist/) and [Anet A8 Powersupply...

Anet A8 Power Supply Adapter Plate attaches larger size power supplies to body frame stock holes without any new drilling required. It fits 150mm x 50mm back screw placement and secures it to 86mm x 90mm holes on the Anet A8 body frame using M4...

I just bought an Anet A8 Plus, which has a similarly mounted power supply to the Ender 3, but then Anet does one better and has their power supply fan vent inward towards the build volume... I needed something to redirect air outside of the build...

They both broke because they were a little too small, maybe the size was measured for the old Anet A8 power supply. This case is designed specifically for the 2016/2017 Anet A8 power supply. Key features include: - A slot for a three-pin socket -...

This is a straightforward mounting bracket for an 80x80mm fan, specifically intended for the original power supply used in the Anet A8. The holder's design takes advantage of the existing mounting holes within the frame, making it a breeze to install...

Support for 120mm fans in the original power supply of Anet A8. It attaches solely with a top screw while the rest of the piece fits snugly within the side flap. Two additional holes for screws are present on the other side, yet they remain unused.

I thickened up the parts in V2 to make sure they print smoothly. ...Since no 92 mm fan adapters were available for the Anet A8 power supply, I made one myself. Hopefully it will be useful to you! ...I also added a cover for thicker 33mm fans.

This is a power supply and fan 12x12cm cover for Anet A8, making it with supports would be the way to go. ...I put the face "MECATRONICA" on the heated bed like in someone's image, but you can try another configuration.

Remixed Anet A3 Power Supply Cover with Switches and Plug by Hoeb. I adopted the mounting system from the original design, incorporating it into my own cover. Cooling holes were added to enhance airflow, along with the ANET A8 nameplate. ...The small...

This custom casing was designed specifically to accommodate an 80mm fan that is mounted on the power supply, which comes standard with the Anet A8 printer. The design builds upon the concept of a previous fan case found at...

This fan shroud directs airflow away from the print bed on Anet A8+ power supplies, resolving quality issues with prints, especially tall objects in vase mode. It also reduces noise from the power supply fan as an added benefit. I observed similar...

I Design an Innovative Power Supply Case for the Anet A8 3D Printer. The Customized Enclosure Measures 114 mm in Length and 50.5 mm in Width, Ensuring a Perfect Fit for the Printer's Compact Size. To Accommodate the Switches, I Precision-Engineered...

... fan cover, as shown in the picture below. It's simple yet effective. Printer Settings Printer: Anet A8 Rafts: Yes Supports: Doesn't Matter Resolution: 0.2 Infill: 70% Notes: ABS Post-Printing The quick fix for power supply fan mounting works great.

I designed a casing to fit a 40mm fan that sits on the power supply of my Anet A8 printer, especially when room temperatures rise in the summer and the power supply gets hot. This little fan case brings the temperature down to a safe level. I...

Old power supply finally gave up, had a spare ATX power supply lying around, so I printed this to sit on the right side of the printer. Use the balancer if you don't intend on printing the second part (under the power supply), it's still being fixed...

Donate: https://www.paypal.me/mrstanlez I've created a compact enclosure for a switching ON/OFF power supply designed specifically for the Anet A8 3D printer. For further details, please refer to the accompanying images. ... The materials required are...

This is a remix of Case Fan (80x10mm) Anet A8 Power Supply by Black-Demon\r\nhttps://www.thingiverse.com/thing:2043548 V.1.1: Bug fixes were made to ensure a smoother printing experience. I had an 80x25mm fan and wanted to attach it to the power...