anet a8 upgrade extruder 3d models

Based off of LittleMrJ's i3 A8 Badass DiggityDank MK8 Carriage A Fully Enclosed Extruder with customer Carriage for the Anet A8 Direct Drive Extruder Head. Includes an embedded cooling nozzle, mounts for the blower and heat-sink fan, holes for...

I specifically designed this to accommodate my Noiseblocker NB BlackSilentFan XM2 40mm fan, but other 40mm fans should also fit (the Anet A8 stock fan is a likely candidate, although it has not been tested). The bottom edge of the holster features...

simple screwless LED Stripe Mount for Anet A8. usable with 8mm x 50mm or smaller stripes. ... V2: similar to v1, only the angle of the strip is inclined towards the nozzle

... 100 or 150mm height. So why not try doing it like Prusa? Cables should go backward, allowing me to print up to maximum height now. You can find all my notes, recommendations, and mods for Anet A8 at https://www.mikrom.cz/3d-tiskarna-anet-a8/.

BMG type extruder support with direct hotend, plus support for layer fan for Anet A8 printer. You need something like this (right): (Set 3, for V6 block) https://es.aliexpress.com/item/33013818755.html?spm=a2g0s.9042311.0.0.274263c0pMfgMv Suitable...

It's printed with an Anet A8 straight out of the box. I've created it entirely with Tinkercad after checking out many alternatives online and especially here. The rails hold the strip (just three LEDs), the two holes at one end are for stopping the...

Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 40% Filament: MG Chemicals ABS silver Notes: Only a little bit of support (touching the bed) is needed, though I accidentally printed mine without and...

Note: This and future projects are now available on Printables, see https://www.printables.com/model/165992-am8-anet-a8-biqu-h2-v20-extruder-mount . This design replaces the stock X carriage bracket of a Anet A8 / AM8. The backplate features a...

I've upgraded my setup to "work in progress" now because the carrier was flexing a bit between the extruder and the hot end. When filament is retracted then extruded again, I could see the hot end getting pushed down away from the extruder as...

The original design won't fit my Anet A8, so I've remixed one that suits it perfectly. extruder end: • add hole for extruder motor wire • make space for easy filament replacement • remove unnecessary upper spacer • simplify elements for a more...

This is my dual blower E3D/E3D V6 Clone extruder head for an Anet A8 Style Printer. I have included a BLTouch and an Inductive Sensor Mount. The Blower Cover MM is optional but I would appreciate it if you printed it and displayed it proudly. If you...

This design replaces the stock X carriage bracket of a Anet A8 / AM8.The backplate features a mounting pattern for a BIQU H2 V2.0 extruder / hotend, using 4 attachment screws. A second part features attachment points for a 5051 blower fan, an...

This is a custom design for the Anet A8 with a self-leveling sensor of the TRONXY type. It's a remix because I added a female connector to make it more stable. ...The original version, despite having four ergonomic handles, still had a tendency to shift...

... for extra grip and comfort. ...To secure it further, I added ziplocks that tighten as needed. Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20-100% Notes: Simply mirror the object to print the other side's part.

Designed specifically to fit snugly atop the Anet A8, it's perfect for Bowden setup enthusiasts who crave precision and control. ...The tiny squares are thoughtfully placed for securing zip ties, despite the somewhat tight fit that still ensures a...

Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: .20 Infill: 40 Notes: The print took about 30 minutes. Post-Printing Refer to SentinelRX5's post for step-by-step installation instructions. ...Make sure to install the mount onto...

This is an X Axis Leadscrew and E3D V6 conversion for the popular Anet A8 3D Printer... The plan is to run a bearing supported leadscrew with the X axis motor end mounted on the Left. The main carriage is significantly smaller and should be...

Instead, use the duct available at: \nhttps://www.thingiverse.com/thing:2121279\nI've printed numerous coolers for my Anet A8 printer and encountered several issues. Some were too bulky, others too heavy, while some didn't fit due to being either too...

The original doesn't fit on my Anet A8. So I remix my own one. extruder end: • add hole for extruder motor wire • extruder could now opened to replace filament • remove upper spacer • reduce elements • enlarge size deep to reduce collusion from...

Update 19.2.2017: I've uploaded a new version, "Mistral 2", as an alternative depending on your needs: http://www.thingiverse.com/thing:2121279 Print Settings: * Printer: + Anet A8 * Rafts: + No * Supports: + Yes * Resolution: + 0.2 * Infill: + 100%...

I upgrade the popular Extruder Fan Mod V2 by hadoko, found on thingiverse as thing:2290361, with a custom-designed front section capable of securely holding an Autolevel Sensor LJC18A3, featuring a diameter of 18 millimeters.

The adaptation is for the original dented gear shiped with the Anet A8. mods: - changed some values in the .scad code ( check original and this for diffs comparison ) Now the idler curved cutout, near pivotal joint of the idler, adapts...

Designed to use if you have already printed this Bowden E-Stepper mount: https://www.thingiverse.com/thing:2369063/files Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% to 25% Filament: 3D Solutech PETG or PLA...

This is a Custom Filament runout sensor mount with/without a Bowden E-Stepper motor mount.\r\n\r\nEngineered to sit atop the Anet A8 acrylic frame on the right-hand side. Removal of the small acrylic paddle securing the smooth guide rod is necessary...

Unfortunately, its original positioning proved to be a major flaw - the fan holder sits too high, inadvertently cooling the hot end rather than the filament emerging from the nozzle on my trusty Anet A8. To address this issue, I cleverly added...

I needed a holder that mounts two extruder motors and created this remix. I added a dual-color version as well! Make sure to also check out my video about the dual-extrusion upgrade. Have fun with this model! ... #### Edits 3/19/2018 - Style of links...

This modification helped, but it also made cleaning the extruder and replacing filament extremely easy. I've also included a handy filament guide in this design. The original heatsink wasn't doing anything anyway, so I got rid of it. My design pulls...

After upgrading my Tronxy P802MA with a high-performance Mk10 extruder upgrade from AliExpress, I installed a MicroSwiss all-metal hot end and throat. However, the heat soak issue persisted, so I needed to find an effective way to cool the metal...

I converted to a bowden setup on my A8, and I was dissatisfied with every solution I found to mount the filament spool on the frame. So I designed this, it's one piece that mounts to the top of the stock frame, right side, and holds both the extruder...

This is a 40mm cooling fan adapter I created for my Anet A8. Initially, I printed a copy of a similar one (thing 2051184), but then I reverse engineered it and made some modifications based on its good design. One thing that bothered me was the...