anet a8 thumbwheel 3d models

This stand holds a spool for the Anet A2 printer on top of the device next to its display screen. It has a small pocket at the bottom that grips the corner tightly. I secured it in place using velcro but you can opt for a zip tie or any other method...

I have an Anet A2 Plus with a 270 bed. At this time, I did not feel compelled to utilize the full extent of my heated bed for printing purposes. Instead, I opted for 220 glass due to its greater availability. To secure the glass to the bed, I am...

It is a rail mount for my Anet ET4 (which uses 20x20 aluminium profiles) to fit a 7" display from waveshare. It fits for M3 screws, >=16mm length. I left some room for the connectors and also for the nuts. This will likely be updated soon as I...

I am currently modifying my Anet E12's extremely flexible Y-axis linear rods by replacing them with a pair of MGN12 linear rails without wanting to invest in a new Y carriage yet, so I designed this adapter plate to utilize the factory SCS8UU...

Notes: Printed on Anet A6, 0.4mm nozzle, 0.2mm layer thickness. Support is required for one of the corners of the top lid, the vent arches have a single line support "built-in" that easily breaks off. ... My printout features 3 bottom and 4 top solid...

Parts: Micro SD Extension Cable: https://www.amazon.com/LANMU-Extension-Memory-Extender-Linker/dp/B01D9J8KQE/ref=sr_1_1?ie=UTF8&qid=1482038934&sr=8-1&keywords=TF+To+Micro+SD+TF+Flex+Zip+Extension+Cable+Adapter Print Settings Printer: Anet A6 Rafts:...

... to be safe. Works well for my Ender 3, Ender 5, CR-10, and Anet A8Want More Free Designs? ...Like and Comment! Instructions:Load in Cura Slicer and be sure to use these settings:Layer Height: 0.2Line Width: 0.4Infill: 100%Build Plate Adhesion: None

I fabricated an enclosure for my Anet A6 and required ventilation so I created a support to hold the fan and the 4-inch air duct. The part fits snugly onto the crimped end of the air duct, allowing you to increase the radius of the duct support if...

my settings where: CURA front shock mounts I printed flat Back mount I printed upright with 60% overhang angle support 0.3mm (extra fast) skirt (2 layers) printed on my Anet A6 this is my first remix, I hope to upload much more unique files in the...

I designed this because I don't trust the tiny MOSFETs on the RAMPs board any more than I trust the ones on the factory Anet board, but the MOSFET was hard to mount in any reliable or attractive way. This has a standoff of around 12mm to allow for...

Print 40% infill Tri-Hexagon, lowest possible temperature with great layer adhesion, mine is 205 for pla anet, It prints around 10hrs. 115g I took the basic idea from a printable subwoofer here, and thought that i can improve only the tube of the...

I modified Ruben472's design for my Anet A6, enabling me to print it in two colors using its single color extruder. The logo's design was simplified this time around, eliminating thin sections that made the previous process so much more complicated....

... printed this in cura and you may want to toggle the setting ignore small z gaps to have no slicing errors on the bottom layer after the support. Print Settings Printer: Anet Am8 Supports: No Resolution: 0.2 Infill: Any Category: 3D Printing Tests

Print Settings: Printer: Anet A6 Rafts: No Supports: Yes Resolution: .1 Infill: 50% Notes: Since I was new to printing, I chose 50% infill to guarantee that part would be robust. ...It has held up exceptionally well over nearly a year without any...

This spool holder clips onto the EMT conduit and was designed to be mounted at the top of an Anet EMT8 conversion. If the fit isn't tight enough to hold a spool on its own, a screw can be used to secure one or both of the mounts. ...An optional shorter...

The smaller version was printed in "smokey transparent PET-G," boasting a 0.2mm resolution and a 0.4mm nozzle, all set to "spiral vase mode" on my trusty Anet A6 with a flow-rate of 80%. In contrast, the larger one is made from "green transparent...

I tried out several sensor mounts for my Anet, but none of them seemed to be the answer. So I started from scratch. I used the v6 clamp area from the original cap that came with the customizable bowden carriage, and basically reworked everything...

Created this mount to be able to use the Foxeer XAT600M on this frame, it should also work for other cameras with same size. The file has both sides to print at the same time, it should be printed in flexible filament as it has a tight fit. Print...

The X-Carriage for the Anet A2/Tevo Tarantula underwent tinkering, resulting in a design that includes a Belt Tensioner. The tensioner was made thicker and the holes for the MGN12C were replaced with MGN12H. After printing it out, I am currently...

This design is suitable for printers: ADIMLab Alfawise U10/U20 ANET E10/E12 Athorbot A01 Creality CR-10/CR-10S FLSUN Plus/FL Geeetech A30 HUAXU3D X1 JGAURORA A5X KOHON KH01 KREATEIT KR - 10S Lavewatch LW - 10A RAISCUBE R10 / T8 / T9 TEVO Tornado...

... along X, same with Y or mix X and Y lines. Same with squares, only one in the middle or ever you want. Print Settings Printer: Sidewinder X1 Rafts: No Supports: No Resolution: 0.2 Infill: 0% Filament: Anet 3D PLA Yellow Category: 3D Printing Tests

... experience. I've added some pictures to help you choose what to print easily. Have fun printing! Models shown are printed using the Anet E10 and Creality CR-10. ...You can purchase your own printers here (affiliate links): Printers on Gearbest.com

... Glue the magnets in with 5 minute epoxy. See my magnetic building board lever clamp here: https://www.thingiverse.com/thing:2540725 Print Settings Printer: ANET A-8 Rafts: No Supports: No Resolution: .2mm Infill: 10% Category: R/C Vehicles

Creality, TEVO, Prusa, Anet, Ultimaker - 100% printable with good result. I use Ender 3/TEVO and about 4-5 hours to print this model. May be you need nailfile to smooth edges. You have to make some post-printing work: sand, prime and...

This adapter holds on charger only by thight fit - only if you print it right This works only with CHINA charger IEC connector:...

This is frame replacement for GEP Rc LX5 Frame that allows usage of Caddx Vista Tx and DJI FPV camera. Frame will fit DJI Air Unit but mounting holes wont match. Print Settings Printer Brand: Anet Printer: A6 Rafts: No Supports: No Resolution: 0.1...

The only compatible thing might be an anet Z axis standard (space between lead screw and linear rod). Everything should fit easily. It is designed for 8mm rods. Carriage files should be in separate printable model.Print each model once.You need:6x...

I made this case to protect my USB HD Printed in Anet PLA everything snaps together print setting are included in print setting.png file highlighted in yellow printed on my ender 3v2 in about 4 hours fits 2.5inch drive L115mm x W80mm x H21mm seems to...

This is a very simple spool holder designed for 3D printers built with a frame made with aluminum profiles measuring 30 x 30 mm, such as ANET AM8, Prusa Clone, etc. The idea is to build a very simple but functional spool holder, consisting of a...

HrEM is Harmonic EQ Mount with OnStep controllerGear ratio is 1 : 404.1818 ( 1+46/11)*78Source code on GitHubBOM2 x 6010ZZ bearing2 x 6807ZZ bearing12 x 606ZZ bearing2 x 17HS4401S-PG5.18 or 17HS4413AG5.18-X Stepper motor2 x CL-70N Swis Arca Clamap or...