anet a8 spool holder 3d models

Top mounted spool holder for the Anet A8, a Prusa Replica that holds a 1kg spool in place with ease. To set it up correctly, you'll need an 8-inch threaded metal rod. Print settings: A minimum of 50% infill is required to ensure stability. A raft...

I designed this spool holder specifically for my ANET A8, a top-notch 3D printer. ## Minimalist yet robust design I'm not one to waste filament on printing unnecessary components, so I took it upon myself to create my own optimized spool holder...

I designed a custom spool holder to keep my Anet A8 frame organized by mounting it on one frame. The TPP-SPH001RH-1 attaches to the right side when looking at the printer's back, while the TPP-SPH001LH-1 mounts on the left side. I recently made some...

Here is a large spool holder for the Anet A8 that can accommodate up to four filament spools. It's loosely inspired by https://www.thingiverse.com/thing:1624641 but designed from scratch before realizing its SCAD was available, my mistake. I used...

Here is a large spool holder for the Anet A8 that can accommodate up to four filament spools. It's loosely inspired from https://www.thingiverse.com/thing:1624641 but designed from scratch before I realized its scad was available, my bad. I used...

This is a spool holder for the Anet A8 that attaches to the screws of the LCD module using the Anet provided M8 threaded rod. The stack of components on the LCD module's screws should be: front plate, standoff, LCD PCB, M3 nut, back plate, and...

After experimenting with various overhead spool holders, I discovered that none met my expectations. I decided to create one from scratch, envisioning a design where the spool rod and nuts would hold it together on both ends at the top. The bottom...

After smashing the acrylic corner on my spool holder, I took a serious look at other spool holders. There was nothing out there that really had the appeal of the basic spool holder that came with the printer. It did fit any spool, it worked well when...

Here is my design for a spool holder's axis using the original Anet spool holder with no bearing.\r\nAs usual, you can find the FreeCAD data to modify the design according to your needs.\r\nPlease note that the thread must be machined. You must screw...

There is only a little for the A8 Plus, so I've built a spool holder. The axis serves as a rod with an 8 mm diameter and 120 mm in length. ...(I had another completely scratched linear bearing axis left over) As spool wheels, there are two versions:...

Fit perfect for Anet A8 Plus. i glue the bearing. ...I think its safer :) This is a Remix of https://www.thingiverse.com/thing:2537713

More one great creation of Perfect3D to upgrade your Anet A8! Fast print, light weight, fits on original drills of Anet's Front Face, clean and beautiful design, extremely essential upgrade. Turns the filament changing, more practical and simple.

**Print Settings** * Printer: Anet A8 * Rafts: Doesn't matter * Supports: Yes * Infill: 30 **Overview and Background** The Spoll holder is being tested for its effectiveness. **Lesson Plan and Activity** None. ... **Materials Needed** PLA or ABS,...

Mount the printed material twice onto the spool holder provided with the equipment.

... the rod that comes with the kit, saving you from buying a longer one! ...Have Fun! Print Settings Printer: Anet A8 Rafts: Don't worry about it Supports: No Resolution: 1.6 Infill: 25% Notes: Use 30C Bed heat and Blue Painters tape to make removal easy

Another versatile spool holder that spins smoothly and effortlessly holds all the spools I've tested so far. ... Customization options are readily available - just modify the provided Fusion file to suit your specific needs.

... another user had created (https://www.thingiverse.com/thing:1975954). ...The adapters fit perfectly and kept the board precisely where it needed to be, but due to differing dimensions, the adapters and spool holder arms didn't mesh together seamlessly.

For those who'd rather not bother with filament spools on their printers. ...Enjoy the convenience!

There's a blank front plate, 2 washers, the reel center, and the spool holder for the back. The filament comes off the reel and goes straight to the extruder. You will need to print two washers and the reel center is designed for Inland filament...

... guide - you can see that it's black in the picture. To get the best results, print this holder with full supports to make sure the "saddle" at the tip turns out correctly. ... Print Settings Rafts: No Supports: Yes Resolution: 0.12 Infill: 20

Spool Holder "Holders" for secure attachment via screws, specifically designed for the Hesine M 505 Spool holder. ... Print Settings: Printer Brand: RepRap Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 100%

If you're one of the fortunate owners of an Anet A8, you already have a basic black spool holder consisting of two "A" pieces and a short threaded rod. It functions but is genuinely cumbersome and uncomfortable. Based on these points, I decided to...

... mm diameter version has been added to the adapter. Print Settings: Printer Brand: RepRap Printer: Anet A8 Rafts: None needed Supports: Not required Resolution: 0.2 millimeters thick layers Infill: 15 percent filled with strong and stable material

Heavy-Duty Extension for Anet A3 Pro 3D Printer Spool Holder - Supports Up to 9.9 lbs of Filament Weight

I've modified the spool holder frame, as seen here: https://www.thingiverse.com/thing:2026493 by Speedy4433, and the spool center, which I've customized to accommodate a wider spool, can be found at this link:...

I designed a spool holder to reuse the original Anet A8 8mm rod with minimal modifications. The holder slides onto the body frame without the need for screws, reducing hassle during installation. I connected the stem to the base using extra M3 screws...

Spool holder reuses original Anet A8 8mm rod perfectly. Holder glides onto body frame without screws, eliminating the need for tedious assembly. M3 screws from the extra original parts secure the stem firmly to its base. This design enables...

At this point, I decided to modify the spool holder (as I believe Soeren Stobbe's spool holder is exceptional) to make it fit perfectly. In my project, I also created a standard bracket, which you can see in the preview. The pins for the bearings...

Hi Everyone, this is my design, thinked for holding the Sunlu spools. It works with the 608 bearings. The bearings holes are a bit larger, because you can leave the debris that are difficult to remove, when you cut the supports inside the recess,...

Adapter for any coil, perfect for the filament holder that comes with the Anet A8 printer. The bobbin spins effortlessly thanks to this adapter. To assemble the adapter, you'll need to print two brackets in addition to a threaded rod and a pair of...