anet a8 spool holder 3d models

... original, which was a bit too tight. I just tested it and it fits perfectly now. Enjoy! Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 layers Infill: 0% Notes: 18 minutes. ...I use skirt settings with masking tape also.

For those with 12mm inductive sensors, refer to Thingiverse's design: http://www.thingiverse.com/thing:1884118 Print Settings: Printer: Anet A8 Rafts: No supports are needed. Resolution: Set the resolution to 0.2 mm. Infill: Opt for a 20% infill...

This is a holder for the 3mm glass on a 3mm Anet A8 heated bed. I extended the side walls to ensure they stick about 0.2mm above the glass and added holes for a 3mm screw. Although the holders fit snugly, additional support is required. The screws...

Here's the brass brush and heatbed wire holder for the Anet A8. It requires removing your heatbed, as it is mounted on the front left, atop the aluminum H frame using bearing block bolts. When tightening those bolts, don't forget to move the Y axis...

... put around two 8x22x7 bearings. ...It uses the standard threaded rod and spool frame that comes with the printer. It's suposed to let the filament spool spin more freely. ...There are two M3 Bolts and nuts required for claming the two shells together.

... put around two 8x22x7 bearings. ...It uses the standard threaded rod and spool frame that comes with the printer. It's suposed to let the filament spool spin more freely. ...There are two M3 Bolts and nuts required for claming the two shells together.

For those who have correctly assembled their bed plate holder by deviating from the standard Anet A8 assembly instructions, this device may not be suitable as the belt height would already be in alignment with the pulleys. Key benefits of this...

Sensor Holder Mount for M18 Capacitive and Inductive Sensors on Anet A3 3D Printers

... the need to insert my fingers between sensitive electronics to retrieve the card. The holder securely attaches to the front panel of my acrylic-frame Anet A8 3D printer, requiring no glue or screws - it simply locks into place for easy access.

... fingers between delicate electronics to access the card. The holder secures the micro SD card in a prominent position on the acrylic frame of my Anet A8 3D printer, without requiring any adhesives or fasteners - it simply locks into place with ease.

I was searching for a TL-Touch holder for my Anet A8 that wouldn't force me to remove the fan or heatsink. I also wanted to be able to print in PLA. Since nothing suitable existed, I combined 3D-Touch mount from here...

Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: To ensure proper installation, the support screws must be threaded into the bearing holes (M4). ... Post-Printing: This design is specifically for capacitive...

I really liked the spool mount by Igal, but it wouldn't slice right in Simplify3D, so I remeshed it and did a little work in Simplify3D and this is the result - it printed fine for me in PETG and is much better than the result I got with the initial...

Remix to accommodate the mounting of the 3D printed MOSFET V2, significantly larger than standard MOSFETs, onto the Anet A8. ...This upgrade requires installing the MOSFET vertically beneath the control board for optimal functionality.

I'm taking my Anet A8 to new heights by streamlining the Micro SD card insertion and removal process, a challenge many users face. ...To overcome these obstacles, I've redesigned the component from scratch.

This design caters specifically for a 120mm PC fan, which can be fitted onto the Anet A8's power supply unit. ...You can find more details about this model on Thingiverse at http://www.thingiverse.com/thing:2235577.

Reworking of the Thingiverse model 1666094 was undertaken to achieve a superior fit with the lower linear bearing on the X-axis carriage of my Anet A8 printer, which the original design struggled to accommodate effectively.

I support the Titan extruder on the upper right side of my Anet A8. ...I position the motor forward so that the bottom wheel doesn't touch the chassis.

This device is designed to replace the standard bearing blocks (SCS8UU) on the Y-axis of the Anet A8. Since the SCS8UU is commonly used, this device should be compatible with various other printers or even the X-axis, given its identical distance...

An Y-Axis GT2 belt holder suitable for the heat bed frame holder from Bohrers Shop (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html) but it should also fit on the stock Anet H-frame (the holes do) and definitely on other...

An Y-Axis GT2 belt holder suitable for the heat bed frame holder from Bohrers Shop (https://shop.bohrers.de/heat-bed-holder-anet-a8-und-a6-kommt-in-kuerze.html) but it should also fit on the stock Anet H-frame (the holes do) and definitely on other...

... together and implement a stepper screws raiser plate too. #TESTING: I'll be testing and reporting effects of each upgrade in my review of this frame at http://mirko.vukusic.net/3d%20printing/anet-a8-tatara-steel-frame-by-orballo-printing-review/.

... The following conversions are also supported: 2020/2040 extrusion, Anet AM8, and Cube printers. Print Settings: Printer: Anet A8 Rafts: None required Supports: Yes Resolution: 0.2 mm Infill: 25% solid with three shells or 45% solid with two shells

Remixed TNS sensor holder now accommodates Tronxy or Anet sensors seamlessly, ensuring a perfect fit without any modifications required.

The Anet A8 Plus features a smaller front fan angle, but the sensor consistently fails to measure accurately. Sensor Holder v2 requires minor adjustments. To calibrate an 18mm sensor: Define X_PROBE_OFFSET_FROM_EXTRUDER as -26. This value...

Rear Anet A8 X Belt with BL Touch Holder - a remix based on creations by zumili and matsondawson. The probe is positioned at the rear for a cleaner look, utilizing one M3 nylon nut as spacers. Several configurations need to be modified to make this...

A cable management solution for the Heat Bed of the Anet A8 3D printer has been designed to keep cables organized and out of the way. This design attaches directly to the springs of the heat bed, preventing interference with the nozzle, especially...

The Prusa i3 A8's filament guide is a movable part that enables easy removal and installation of filament spools during printing operations. This design allows for smooth filament feed, reducing the likelihood of entanglement or breakage caused by...

I chose to install some additional illumination on my Anet A8 printer, but attaching the LED strip using standard adhesive tape proved to be a short-lived solution. Therefore, I created these small fixtures to provide a more secure fit. ...They function...

... power supply. ...The mount fits perfectly on power supplies that have 6mm horizontal hole spacing and 5mm vertical hole spacing, with each row of holes shifted exactly half the horizontal spacing - a standard setup found in many Anet A8 power supplies.