anet a8 spool holder 3d models

The headset rests on two extrusions of the main holder. The controllers are hanged on the arms. The main part can either be wall mounted or mounted to the foot. The foot has canals for cables. The main part in turn has room for cables within the...

Install the PINDA probe into its holder with the wire looped on the inside of the probe as directed by Prusa. Push the remaining coolant line through its hole in the x-carriage below the lower bolt and loop it around between the fan and extruder to...

When you want to use non english language, go into "Language Packs" folder and copy your language to the root (folder above) ### Firmwares to download: * firmware_Genius_BL-Touch_Marlin2.0.9.3.hex * artillery_tft_fw_1.27.x_patch_9.1 - Genius Mod.rar...

### Printing and casting the silicone brush First, print brush_holder.stl, brush_lever.stl and brush_mount.stl in PETG or ABS with your default settings and 50%+ infill. Next, print brush_mold.stl in PLA (it is important) with following settings: ...

The base parts are:Floor & Base parts:1) Base (Base - Giant.STL)2) Flat Base (FlatBaseMain.STL & FlatBaseMain - No Holes.STL)3) Walls (WallBrick.STL, WallMesh.STL & WallStandard.STL)Main Building parts:1) Building Walls (BuildingBack.STL,...

There are also useful coat hangers and finger toys.Or just check out all my creations.Sources:This design is based on Mahjong Game tile holder, copyright 2011 by choffee. Thanks for sharing!</p><h3>Print instructions</h3><p>You can print it without...

Use this if you want to add your own supports. "label" STL files: two kinds of signs that you can use to label the data (if you print the variant with label holes (the STL with supports also has label holes)) Thank-you: Big thanks to Stibiac for her...

Importantly the rear axle holders are part of the motor cover, making it easy to remove the axle if needed. - The cabin allows for longer batteries to be used as the servo has been positioned further at the front. - The servo motor provides a...

1 x Demolition Fist for left handed arms (mirror before printing for right handed version) 1 x Hellstorm twinned arm cannon for right handed arms (mirror both the cannon and arms for left handed versions) - (Multi-Shell) 3 x Ammo belt-feeds for...

So I made the holder for the winch hook on a snorkel's place, especially we broke snorkel some time ago. Just in case, the detail is also in the materials. If you need Panhard Rod for a rear axle it is here...

2 x power switch (one to switch off the pump if necessary, one for general on/off) 1 x fuse holder and a 3A fuse (50x20 mm) 0,5m x Transparent PVC tube 6mm inner diameter: 0,5 m x Transparent PVC tube inner diameter 9mm:...

I learned a trick on my slicer to create areas of higher walls or infill, so i plan on using that when printing to try and optimize usage, ill prolly do a brief tutorial on it who knows :shrug: I also got my aluminum extrusion i will cut to length...

The two files with a trailing "o" are optional replacement parts for a first row with greater diameter holders as described above. You will need one cut of each file to complete the paint rack (ok - not including the optional files of course) ...

# Features - Modular Nstrike stock adapter with spring lever - Detent pin for locking the pivoting arm into deployed/folded position - Integrated Magholder or Mega Dart Holder X 4 - Fully printable on a 120mm X 120mm build plate # Requirements -...

You need this to be a nice area to glue the nut holder into place, I suggest supports, it could be bridged but I did not take that risk, its literally less than a gram of supports. Hardware needed: Two to three 608 bearings and the internal...

That will be for a next version.Update 08/01/2024We've now built a first version of this using the following components:Raspberry Pi 22500 mAh lipo batteryWaveshare like TFT screen off amazonan SNES USB controller off amazonA couple things added, a...

The socket should sit within the gem holder and crown pieces and be hidden. Check the length of the rod and trim as needed, it should almost touch the table top when the lamp is upright. Thread a nut and washer on the cord and insert the cord...

2 washers at the top and 2 at the bottom between the bearings and nut holder were used.\nIf you get to this step I should have more photos/instructions showing the rest.\nMORE NOTES:\nAny place that a pulley attaches to a bolt, screw on a nylock...

For instance, to use the JB adapted micro camera with the clear 3 screw micro camera holder. - [ x ] Some method to provide more support for the micro camera. This version, as well as CrazyJ's version, only has a single screw into the camera on each...

- rounded corners - improved holder for the d1 mini mcu - better adapted for available tactile buttons It is optimized for tactile buttons with 2 Pin DIP 6 x 6 x 5 mm (2 pins much easier to solder than the shorter 4 pin types) The icons As to the...

The engine has holders for the working battery and a spare but carrying loose spares is no problem. I pack my spare batteries in my Wife's picnic bag when she is not looking!! Largely 3D printed with some hardware and off the shelf electrics needed...

I've included a solid block for you to design your own custom holder for specific tools. Let me know if theres a specific tool you need to be designed.The Model fits the dimensions of the printer precisely, it sits over the top glass lid knob and...

I printed the iron holder in PLA and so far no problems with heat. It mates to the case with a dovetail joint and is held on with a 3MM X 12MM screw. The battery receptical part has to be printed with supports but block the supports where the...

You won't be able to change the number of links without removing the connector. I've also uploaded a updated version that I didn't print out, so I'm not 100% sure that it will fit, but it incorporates some fixes: Changed M10 thread to M12 for the...

Insert the blower motor into the fan holder body, taking care to route the fan wires through the smaller hole. Secure the fan cover to the fan body with 4* M3X10mm machine screws. 9/16" OD vinyl tubing serves as an air duct between the blower and...

Its Cigarette Tip Holder , but depending on the color of the plastic filament, it will look very nice if you choose the right color to print. I have a lot of different designs! Check out the rest of the collection in my frofile. Filtro de rollo...

Put the whole assembly back into the gantry tool holder, and add the four original screws. Reattach your ribbon cable and filament. ... Redo your tramming, mesh levelling, z-offset and calibration and happy printing with your quieter and more powerful...

In no event shall the authors or copyright holders be liable for any claim, damages, or other liability, whether in an action of contract, tort, or otherwise, arising from, out of, or in connection with the software or the use or other dealings in...

Additional models (to hold the temperature sensor and a secondary thermostat): https://www.printables.com/model/125317-magnetic-holder-for-temperature-sensors-probes https://www.thingiverse.com/thing:5654653 See Assembly Guide PDF at for...

We can then use a simple Cube object to create a cut in the face for the pivot (holder) for this target face. The resulting cut will allow us to build an arm to hold up the face and pivot from the base. You can use the techniques as described in...