anet a8 print head 3d models

This is an Anet A8 Micrometer height adjuster for the print head. The back half fits directly onto the three linear bearing blocks just like the original aluminium bracket, and uses all original screws for mounting. An adjustable dovetail wedge plate...

If you are printing solely for the Anet A8, only the carriage plate, locking levers, and Anet print head assembly mounting plate are required. The carriage plate is engineered to bolt directly onto the bearing blocks of the Anet A8. The locking...

The yarn transport chain runs directly from the card to the print head. I've found that by using WD-40 as a lubricant, I can significantly reduce the amount of maintenance required. Since applying this treatment once, I no longer need to lubricate...

I use this printing head last time because with two Noctua Fans, it's extremely silent and powerful for cooling. Also, I made a "Service position" on this head. You can unscrew the lower bolts and swing it upward so you can clean or replace your...

(I used a knockoff one and I can run 250 degrees on 0.6mm nozzle with no problem), * It requires 2 side fans so be prepared for it, * I am not providing any bowden mount - basically anything will work, so please do your own search and pick the one...

This is a bracket for a Bowden E3D - V6 extruder head, designed to screw directly into our micrometer-height-adjuster (http://www.thingiverse.com/thing:2185918) using 10mm x 3mm self-tapping screws. It features an integrated fan mount for the radial...

This custom extruder head is designed specifically for attaching a 10 cc syringe barrel from the Ultimus V5 high precision dispenser to a commercially available Anet A8 3D printer. (Supplementary Materials Section 9).

The custom extruder head allows attachment of a 10 cc syringe barrel from the Ultimus V5 high-precision dispenser to a commonly used Anet A8 3D printer (as detailed in Supplementary Materials Section 9). ...This information can also be found in our...

A custom mount to hold an engraving laser on the Anet A8 print head was created. The original design did not fit properly, so a revised version with accurate measurements was developed. In my setup, the laser is mounted at a very slight angle due...

... original, which was only half size. ...It failed to get the letters correct, I suspect due to some settings being tailored for a different printer. A new print job was started but unfortunately it ran out of PLA before reaching the lettering stage...

Anet A8 Custom Carriage features a circular fan and fan bracket specifically designed for J-Head style Hot End, utilizing stock items from the Anet A8 printer. The custom carriage also incorporates an aluminum J-Head holder made by B3 Innovations'...

Anet a8 plus Head support bracket. The original head remains, only improving stability and prevents the original head bracket from sagging. Top holes do not print perfect but acceptable. Please enable bridging. When requested i'll print and post an...

This is a compact, fast-to-print cable harness clamp for the ANET A8 printer extruder head. It may also work on other models. V2 has been redesigned to be narrower and more streamlined. Print Settings: Printer: Anet A8 Rafts: No Supports: No...

I discovered that the print head cradle on my A8 had become quite flexible, sagging 5-10 degrees and was extremely unstable. To stabilize the cradle and support the weight of the print head assembly, I implemented a quick fix that made it more rigid....

It's simple to install between the screws on most Anet A8 heads. I've included the SolidWorks 2016 file it was made from, along with a screenshot showing how to set the distance. ...The distance was measured from the front of the bowden mount surface to...

... the spool rolls effortlessly. Print Settings: Printer: Anet A8 Rafts: Yes Supports: No Resolution: 0.4 Infill: 10% Notes: 100% infill on spool supports ensures a solid print, while 10% infill and 1.6mm wall thickness should produce smooth rolls.

Print Settings Printer Brand: RepRap Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.1 Layer Height Infill: 25% Lines Notes: You'll get the best results printing this in ABS, which is a denser/softer plastic and less prone to...

The original design truly caught my eye, but one issue stood out - my diamond head utilized round heat sinks instead of hexagonal ones. To rectify this, I revamped the diamond head and heatsink mount according to my own specifications. ... In addition,...

I'm utilizing this custom-built printer head on my personal printer, which I designed to produce significantly less noise than standard models. The four fans embedded within it allow for optimal airflow while also keeping the noise level in check - a...

This is a construction design for the Anet A8 to carry the Diamond Hotend using ABS materials. You can spend some money if you want to upgrade to better materials. ... For more information, check out this YouTube link: https://youtu.be/F7Q4UL4C1tE My...

These parts are designed to fix the ColorPod on an Anet A8 3D printer. The CororPod converts a reprap style filament 3D printer to a full color powder printer. The ColorPod is a device that extends a regular 3D printer with the capability of...

Print Settings: Printer: Anet A8 Rafts: No rafts will be used for this print job. Supports: No supports are needed for this model. Resolution: The resolution is set to 0.2 layers per layer. Infill: The infill percentage is set to 50 or 60%. ... Set...

Anet A8 end print alarm box V1. This box contains the electronics for an end print alarm and fits neatly into a convenient location. It can hold a power switch, a buzzer, four 10mm LEDs, one 5mm LED, and a pushbutton. The design also includes holes...

Anet A8 End Print Alarm Box V2 This box holds electronics for an end print alarm, placing it in a convenient and practical location. It accommodates two power switches, a buzzer, seven 4mm LEDs, and a push button, with a hole for wires. In this...

Here is a rewritten version of the text: I recently acquired an InfiniDiy (or possibly Anet A8) head holder model, which I believe adheres to global measurement standards. ... On May 11th, 2017, I made some adjustments to include a compact attachment...

Remix Made From: Original Helmet: http://www.thingiverse.com/thing:2038500 Original Fan Plate: http://www.thingiverse.com/thing:2067508 Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 50% Notes: You will...

This is a simple Lasercut Printerhead designed for Anet A8 and E3D V6 printers compatible with Anet A8. Needed materials include 6mm Plywood, two screws with nuts M3, each 60 mm long, one screw with safe-nut M3, 45 mm in length, two screws M3 for fan...

The four 3D-printed parts for each corner serve the purpose of retaining the carbon plate together with the magnets to hold the plate steady when the bed is moving back and forth rapidly. And at the same time, I designed some better bed adjustment...

I've rigged up a simple bracket to hold a single 12-volt LED, which must be 12 volts, to illuminate the nozzle for my Anet A8 (and similar printer designs) setup. ... I've hardwired mine into the heatsink cooling fan so it's always on when the printer...

Adapter for BLV MGN12 Anet/AM8/Prusa mod for aluminum head installation:...