anet a8 plus x belt tensioner 3d models

I created an upgraded X-axis tensioner for my Anet A8 printer using FreeCAD (blueprint attached). It provides a snugger fit, allowing me to utilize a 16-tooth idler bearing with an M3 screw. To install the tensioner, I need two M4 screws and nuts,...

... to it. This x-axis tensioner for the Anet A8 boasts a .4 inch width for the idler pulley, which is significantly wider than the original .335 in width. ... Additionally, the intended hardware for this setup consists of 1/4-20 nylock nuts and bolts.

I'm upgrading my Anet A8 Prusa I3 printer's x-axis to use a GT2 belt and a custom-built tensioner. The YouTube video at 300 seconds explains the process, but here are the details: I designed and printed the new tensioner using PLA filament. ...It has an...

I tried sanding out the inside of the X-axis tensioner, but I still ended up with too much friction and skipped steps because of it. This x-axis tensioner for the Anet A8 has .4 inch width for the idler pulley instead of the original .335 in width....

I am absolutely fed up with the various solutions I've tried from Thingiverse for X axis belt tension on my A8. It's been a constant source of frustration since day one with this printer. Now that I'm done venting, I'd like to introduce an entirely...

Eje X Adjustable Belt Tensioner

... the M8 nuts into the x-tensioner. Next, mount the pulley within the x-tensioner, making sure the belt is already rolled up. Finally, secure everything with the M8 screws. ...I recommend printing a couple of M8 knobs to make handling them easier.

Customizer tailored specifically for Anet A8, engineered to optimize performance of the 2GT-16T-3B-6 16-teeth idle pulley.

This remix of ToXIc's X axis belt tensioner version fits seamlessly in the newer injection molded x carriage. The original design was too large, requiring extensive sanding to get it to fit snugly, and even then, it remained tight. The bolts on the...

A remix of the original ANET A8 X-axis belt Tensioner (x-Achsen Riemenspanner) M4. **Changes** * The idler slot has been slightly widened. * The width of the entire tensioner has been beefed up. * An M3 nut and a countersunk M3 screw head have been...

Print Settings Notes: Printer: Anet A8 (customized) Slicer: Simplify3D Infill: 40% (fast honeycomb) Supports: yes (both) Wall layers: 3 Top and bottom layers: 3 Speed: 100mm/s Post-Printing At the beginning, bearings are really tight but the rod...

The original design by Freemark is excellent, but I took the initiative to remix Freemark's x belt tensioner and make it my own. With Inventor, I reimagined the design with strategically placed fillets to give it a sleeker look. To cater to my...

... metal pulley with no reduction in print area. ... Pulley Details: Teeth: 16 (T) Pitch: 2 millimeters Bore Diameter: 3 millimeters Belt Width: 7 millimeters Additional Components: M3 Nut x 1 M3 Screw, 20mm long x 1 M4 Nut x 1 M4 Screw, 35mm long x 1

Anet A8 X-axis Belt Tensioner Maintenance Tips and Tricks

This combo X-Axis Tensioner and Camera mount is specifically designed for use with a Logitech C270 camera. To assemble, you'll need two M3 nuts, one M3x10mm cap screw, one M3x20mm cap screw, and two M3 washers if desired. ...The camera will be mounted...

A custom x axis tensioner designed specifically for the Anet A8, ensuring it doesn't slip or run out of adjustment room. Constructed to be mounted directly onto the extruder frame, this innovative device relies on a sturdy M3X20 screw and a durable...

... This is a different X Axis Belt Tensioner for Anet A8. It's based on the one by WedgeSD. CHANGES: -The bars (guides) of the inner piece are now separated from the piece itself, so you can print the inner piece vertically and the bars horizontally.

The problem has been resolved by combining it with an improved tensioner and a custom simplify3D tensioner. This fusion eliminates all problems. Many thanks go to Lokster, the creator of this thing on Thingiverse...

Press the 2 clips into the mount then slide into the right side of the X gantry, the clips should sit on the rods. If mount is resting on the white plastic, print longer clips. 7. Put the arm in place and screw the assembled knob in place. If...

Another version of X-idler for ANET A8 features an integrated tensioner and brackets designed specifically for M3 nuts. My printer boasts a range of upgrades, including a stiff Y-front plate with a built-in tensioner, which can be found at...

This creation was crafted using Tinkercad's intuitive tools. ...Edit it directly online at https://www.tinkercad.com/things/kezpLClN6rD.

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Added 1mm of width in the center to allow the use of the wider one-piece idlers. All other dimensions are the unchanged. ... Remixed from the following part: https://www.thingiverse.com/thing:3105157

Increased the middle width by 1mm to accommodate larger one-piece rollers. ...Every other measurement remains intact.

I rechecked the dimensions to ensure a precise fit, so I tore down and rebuilt it using my own measurements. ...The parts included four millimeter screw holes and matching nuts, as well as a three millimeter bearing screw identical to the one that comes...

Modified for use with a GT2 pulley featuring a 3mm diameter bore.

This model is an upgrade because I used a M4 screw and as a bearing, a model with teeth.

I love the original design https://www.thingiverse.com/thing:1683070. However, I encountered difficulties tightening the screws as soon as the adjustment stiffened, so I created this knob to attach the M4 screws from the original design and make it...

<p>Added 1mm of width in the center to allow the use of the wider one-piece idlers. All other dimensions are the unchanged.</p> <h3>Print instructions</h3><h3>Category: 3D Printer Parts Summary</h3> <p>Added 1mm of width in the center to allow the...