anet a8 plus extruder 3d models

Print Settings Printer: Anet A8 Plus Rafts: No Supports: Doesn't Matter Resolution: .3 Infill: 25% Filament: Inland PLA Rainbow 2 Notes: Part currently printed in PLA Silk as that is what my only working printer had loaded at the time would recommend...

Print Settings Printer: Anet A8 Plus Rafts: No Supports: Doesn't Matter Resolution: .3 Infill: 25% Filament: Inland PLA Rainbow 2 Notes: Part currently printed in PLA Silk as that is what my only working printer had loaded at the time would recommend...

Hello everyone, I'd like to share my solution for upgrading an Anet A8 Plus printer table with six high-quality ball bearings measuring 5x11x5. This innovative design came into being after the original bearings failed, causing damage to my guides.

... not in use. Be prepared to apply some force to snap the base into place within the extrusion channel. This design is tailored for the Anet A8 Plus, but it should work just as well on any printer with a similar extrusion profile and 8mm guide rods.

The Anet A8 plus was in my opinion a bad printer but cheap as a kit, which cost me only 154 euros. Through aliexpress 2020 v-slot profile ordered and creality parts, which cost me a total of 70 euros including the hotend. What you need: 1x 3D...

This is a 30mm OD X 143mm spool holder tube designed to replace the PVC 20mm X 100mm spool holder tube that came with my Anet A8 Plus. I share spools and spool adapters between all my FDM printers. The spool adapters I use are: ...

All bracketry is new and applicable to the Anet A8 Plus. Features Include: 1. Lightened and miniaturised chain links, 1.4g vs 2.4g for the old style commonly found. 2. Cable installation on the fly - cut out channel on links and brackets for...

Unlike the old Anet A8, the plus doesn't necessarily need the auxiliary dual Mosfets added but this cooling mod is totally necessary. Print any layer height but switch support on to get those clips well supported. Uses the existing case but you...

The stock Y-Axis tensioner on the A8 plus was a notable improvement over the original A8, but still fell short in many areas. This design fixes all of my previous issues with the tensioner. It offers 20mm of adjustment, clears the stock bed and...

I probably tried every X axis belt tensioner for the Anet A8 on Thingiverse. While some are very good designs, nothing was really exactly what I wanted. All of them snapped after extended use. So this is my solution. There are several benefits to...

My Anet A8 Plus kit was shaking violently and vibrating wildly on the z axis while printing. In my search for a solution, I stumbled upon @3Displacement's Prusa Bear X Upgrade which immediately caught my eye. After conducting several test prints,...

I have been looking for a decent stand for a long time to get rid of the vibrations of my Anet A8 Plus, but I did not find anything sensible. But I tried to borrow a soft ball from a children's store from children, it perfectly solved my problem, but...

I have been looking for a decent stand for a long time to get rid of the vibrations of my Anet A8 Plus, but I did not find anything sensible. But I tried to borrow a soft ball from a children's store from children, it perfectly solved my problem, but...

I designed a custom enclosure to securely house my 24v to 12v converter for my Anet A8 Plus, enabling me to attach LED lights directly to the printer. However, the existing attachment points on the converter were flimsy plastic components that I...

Hello, I created this nice tensioner from the AM8 for our A8 Plus. It functions extremely well. I modified the holder to use a 20 GT2 pulley. The tensioner screw is an M4 25mm. You can find all information on the original part site. Check out the...

Improvements for Anet A8 Plus Z Axis That Will Use Standard Motor Supports of the Printer and Standard Axis Position. This modification helps reduce axis wobble and motor position offset in relation to the 20x40 T-slot profile. I recommend using...

A convenient cover-up to shield your hands from screws on the Anet A8's extruder mechanism.

My Anet A8 Plus kit was vibrating and shaking on the z axis when printing. While searching for a solution, I came across @3Displacement 's Prusa Bear X Upgrade which instantly caught my mind. After a few test prints, things where improved but I...

My Anet A8 Plus kit was vibrating and shaking on the z-axis when printing, which made me desperate for a solution. While searching online, I stumbled upon @3Displacement's Prusa Bear X Upgrade, which caught my attention immediately. After conducting...

As part of my ongoing upgrade of my A8 Plus, this is a clamp for the X-axis belt on the carriage. ...This replaces the stock (rather poor) part with a solid one and removes the tensioning facility in favour of an external tensioner (which I've already...

This is a mount for a BL Touch on an A8 Plus. I had found a number of alternative methods, but all looked a little flimsy with a large cantilever. This is Easy to print Easy to mount Strong Integrated cable management I have produced two versions:...

I took matters into my own hands as I couldn't find any A8 Plus versions available, so I created them myself. The original designs are there too, but they came out in a lower quality print. I opted for 70% infill due to stability concerns when you...

I didn't find anything for the A8 Plus Version, so i did them by myself. The original ones are printed too, but in a lesser Quality. I printed with 70% Infill because of stability reasons, when you really want to tighten the screws. I will upload...

I designed these mounts to be uncomplicated and allow the boards to dissipate heat instead of being confined in an enclosure.\r\n\r\nSmoothers...

I wanted to swap out the Z-axis bearings on my A8 plus with minimal fuss. This is a straightforward device that lets you push the old bearing out of its seat by its replacements. I opted for two pairs of IGUS LM8UU bearings, which I swapped in...

For all A8 Plus Users who are not satisfied with the belt attachment on the bed, just like me! Remove the screws, insert the belt in the clamp, then attach it back to the bed. Don't forget that the other side of the belt also needs to go through the...

Mount the Titan extruder from E3D on top of an Anet A8 printer for use in a bowden setup. ... Print Settings: Printer: Anet A8 Rafts: None Supports: None Resolution: 0.2 millimeters Infill: 50 percent

As part of my ongoing upgrade of my A8 Plus, this clamp is designed for the X-axis belt on the carriage, replacing the stock (rather poor) part with a solid one and eliminating the tensioning facility in favor of an external tensioner, which I've...

I discovered numerous squash ball feet on Thingiverse suitable for the A8 Plus, although none were specifically designed for it. These can be bolted directly into place of the stock feet without altering the original chassis height. I measured a 6db...

... Link to instructions on how to hook it up to the original A8+ Board: https://h2lab.org/fablab/a8_bltouch/ (Not, mine, all credit goes to them.) Link to SKR 1.4 upgrade kit: https://www.thingiverse.com/thing:4761697 (Mine, all credit goes to me :)