anet a8 plus dual extruder 3d models

... and I also wanted to move the mount to the bed cross brace. So I used the mounting from the y-axis chain and rebuilt the rest from scratch because the brushes would not slide in cleanly. For the mount I used: Anet A8 Y Cable Chain by sukhoi27

This is an adaptor bracket to allow for the use of the stock Anet extruder when building the BLV MGN mod. It should be noted that i did not use the cheap Chinese MGN linear bearings that the original maker used when they made the mod. My carriage...

I'm unable to locate Dual Mosfet V2 Support listings on Thingiverse. ...In order to remove Two Pillar Washer M3x15 under the Motherboard, utilize the two as supports.

I used the part cooling fan shroud found here - https://www.thingiverse.com/thing:2305368 I also used this adapter to make the stock 40mm fan fit the bowden cold end - https://www.thingiverse.com/thing:2830346 I made a motor holder for the mk8...

The design required more clearance between the mosfets, the A8 board and the longer mosfet boards. To accommodate this need, the following extended version is provided for v2 mosfet boards. This design is a scratch build with general ideas taken...

Fortunately, the screw holes on this stand are perfectly aligned with those on the A8, eliminating the need for any additional hardware. Additionally, there is a zip tie groove available to provide extra support for your stepper motor if needed;...

I designed this accessory specifically for the Anet A8. Changing filament can be very challenging, especially for beginners, due to the difficulty in accessing the nozzle hole. Furthermore, if the filament breaks inside the heat sink, disassembling...

Dual Mount for Chitu MOSFET Module. For Heat Bed and Hot End Use. ... I employed this design: http://www.thingiverse.com/thing:1841124 An updated version is accessible here: http://www.thingiverse.com/thing:2001243 This iteration boasts increased...

I also created a motor holder for the mk8 extruder that not only conceals the motor but also gives the printer a more aesthetic appearance. You can find this design at https://www.thingiverse.com/thing:3298983. Furthermore, you can print a small...

These additional files are specifically designed to be used with this anet extruder fan mod from thingiverse: https://www.thingiverse.com/thing:2290361 My custom parts are attached to the top of the extruder fan bracket, providing a secure hole for...

Based on my dual Extruder Mount https://www.thingiverse.com/thing:2487544, I created this one for the E3D Cyclops. This design should fit the Chimera as well, except for the cooling nozzle. The improvements over the previous model are numerous: The...

With my first attempt, I encountered an issue due to the tolerance of my A8 printer not being small enough to print the holes in the lower part and knobs on the upper part accurately. As a result, I had to make some adjustments. If you have perfectly...

For connecting the Extruder wire to the top of the machine's framework

The human wanted to add some extra flair to the extruder fan.

I designed a Bowden Mount Extruder specifically for the TATARA frame, featuring a sturdy bracket that securely holds the extruder's stepper motor in place. ...The motor is easily removable, allowing for effortless maintenance or replacement as needed.

I'm a helpful assistant screw that propels the filament smoothly into the extruder. ...Typically, whenever I switch filaments, threading them through the extruder usually gets hindered by the tube connector.

This video provides a visual examination of the filament feed system's functionality, specifically its connection to the extruder.

You'll be able to install your stepper motor for the extruder onto the X-axis using this mounting bracket.

I revised the upper section of the extruder motor, requiring a switch to the opposite side. ...The job is complete!

... be updating it soon. The design can accommodate either two extruders and another component or three extruders altogether. ...Edit: The thing broke off when I was adjusting it, so I came up with a revised version that supports two fixed extruders.

***~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~*** This modification involves cutting down the extruder heatsink. In my opinion, the increased airflow more than makes up for this, allowing the extruder to run at least as cool as it does...

Thanks Pierrelesek for sharing a brilliant support extruder design on Thingiverse, specifically the L3K model found at http://www.thingiverse.com/thing:512338.

I'm looking to add an M4 screw holder for my extruder fan mod, and I need a 10mm long screw for the job.

... assistant screw that helps the filament go through to the extruder. ...Most of the time when I change filament, and I tried to thread the filament through the extruder it bumps into tube connector. ... UPDATE (01/02/2019): Dimensioning problem solved.

I printed out and put through the paces about a dozen different carriages and mounts for Bowden extruders with BL touch sensor attachments before deciding to create my own from scratch. This was my first-ever DIY attempt, using the following carriage...

This is an adjustable riser block used to elevate the extruder motor away from the base of a enclosed build platform, providing easy access to the Bowden tube and connection point for the hotend assembly.

This support provides easy access to the extruder, making it simple for users to swap out filament whenever needed. ...The design is based on the original LeoN model found at Thingiverse, with a straightforward modification aimed at enhancing usability.

Here's a simple clip-on motor mount designed specifically for Bowden setup applications. ...I've created two versions, one for the left and another for the right-handed extruder variants.

I recently updated a design by Brogz007, specifically his Extruder Mount model 2146021 on Thingiverse. This design is a great example of simplicity done right. ...I added some extra reinforcement to the sides, giving it an extra layer of stability.

A makeshift fix for my crippled extruder fan, I'm using an adapter that lets me slap an 80mm fan onto the shell of the old one. ...It's no ideal solution, but it gets the job done.