anet a8 mods 3d models

...  Fear not, I have fired my quality control person as I found out they were drinking while publishing models (yeah, it was me, I'm fired).***  I have not mentioned this prior to these two X2 fan mods about the wiring differences I found.

Then, tighten it down.Firmware changesFor this mod on the MK3(S), make a custom .gcode-file with the lines below (put it on the SD & run on the printer) or run these over an USB-connectionM350 E16 - Set microstepping to 1/16M92 E445 - Change the...

After trying to silence my own v2, which I have to keep in my bedroom, I noticed that first of all, there are few mods for it and even fewer that make it quiet. With some technical know-how, patience, and a bit of cash, you can half the noise from...

 we are going to need it to make the angled USB C that gets slotted  into the Decks USB C  Port to align perfectly  accordingly to your build. You know every printer is a bit different and like that you can not be sure that...

This roller does not need to be removed if a (200 mm) spool is resting on a 14mm roller in the last position of a filament slot.For 190 mm spools, use the factory 14 mm roller in the second to last position of a filament slotNOTE: Installing this mod...

Due to cable management issues on Wanhao style print heads, I would have to mod my Z axis (e.g. AzzA's Z extensions) before I could print that height. Scaling for a 1 inch pipe would be even worse; the finial would be more than 205 mm tall, well over...

As an aside, I'd recommend picking up a metric screw set similar to this: https://www.amazon.com/1080PCS-Assortment-Machine-Stainless-Hardware/dp/B09WCZ46VL/ if you decide to start disassembling and modding your printer(s): I like to keep both...

That being said, other than for bridging, no supports should be required.Print with the thin front place of the adapter facing the print bedDon't worry about “weird behaviour”, it's normal :)For me, this printed in 2hrs using a heavily modded E3P. In...

 Solder to switch.Snap switch into panel cutout and glue back side to retain if needed.Tuck mid housing internal wires to the sides to make room for panel installation.Install panel onto mid housing cutout and attach with 4x screws.CompleteMini USB...

that requitre more modding of this mount. I’m not sure how much P90 models there are out there when it comes down to gel blasters. also note only the UNW P90 Classic mag will work in the RUNQI body since the sides of the top rail construction are...

Use and build the mod at your own risk! All parts a printed with black filament, except the skulls are printed in white. But since you have to paint it anyway you can use any filament color you have available. Instructions: First of all:...

Of the X and Y offsets, Y offset tends to create far more issues in i3 style printers and especially cheap printers that use V wheels (that’s why there are so many zero Y-offset mods out there!). This part removes the Y offset to improve the ABL.This...

Due to cable management issues on Wanhao style print heads, I would have to mod my Z axis (e.g. AzzA's Z extensions) before I could print that height. Scaling for a 1 inch pipe would be even worse; the finial would be more than 205 mm tall, well over...

The other mod will be required to mount on my son's bigger handlebars. **UPDATE 9/13/2021**: I added a 1 1/8" handlebar coupler in STL and F3D formats. My son's YZ125 has the bigger handlebars. I also tried out 0.7mmx6mmx100mm springs. They...

If anyone out there is doing it I'd love to know how, but so far I have to use my modded CR10S with a direct drive and even then I have to disable retraction completely, use a crazy extrusion multiplier like 1.3-1.5, and set my extrusion width...

I designed it to fit on my Ender 3V2 with linear rail and dual z-axis mod and I wanted it easily removable so I went for the nice quick tool changer from @properprinting. There are many other designs for syringe extruders available, some quite...

Then, tighten it down.Firmware changesFor this mod on the MK3(S), make a custom .gcode-file with the lines below (put it on the SD & run on the printer) or run these over an USB-connectionM350 E16 - Set microstepping to 1/16M92 E445 - Change the...

Assemble flipflop + flipflop-base + lock-TrayThe tray is a great way to finish the run and to store extra marbles. Print SettingsPrinter: Anet AM8Rafts: NoSupports: No, except for “The Wave” and “Lombard Street”Resolution: 0.2Infill: 20%Filament:...

I was inspired by the Bed Cable Side Chain mod by Whoppingpochard The mod relocates the bed heater and temperature sensor wires from the back of the printer to the right side, routing the wires through the hole in the chassis next to the Z extrusion...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                          ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                          ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                                       ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                          ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                          ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                                       ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                                       ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                          ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                                     ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                          ...

Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">                                       ...