anet a8 laser conversion 3d models

This is a Work-In-Progress document detailing my conversion to a Bowden setup for my Anet A8, as I dislike inserting filament into the stock extruder and want a lighter carriage. The setup utilizes the stock Anet sensor for bed leveling and the stock...

What's needed for the conversion: -Anet A8 -Dremel with 20mm flexible shaft -2X M3.5x20mm Bolts I couldn't find the exact Dremel I used, but this one looks very similar:...

A custom mount to hold an engraving laser on the Anet A8 print head was created. The original design did not fit properly, so a revised version with accurate measurements was developed. In my setup, the laser is mounted at a very slight angle due...

Original file: laser_mount_anet_a8.stl New version: laser_mount_anet_a8_1.1v.stl The new version supports both modules; I recommend printing this one. Video: https://www.youtube.com/watch?v=j7RHM9WuDvk DISCLAIMER: Working with lasers is extremely...

This plate adapts the direct drive version of Gavitka's BMG conversion extruder to the Anet A8, using stock A8 bearing blocks and your favorite belt clamp. ... Check out https://www.thingiverse.com/thing:3518138 for both models, which are still...

Conversion to the Anet A8 to Corexy system, where the structure changes and all possible donor parts are utilized. ... Videos with the assembly explanation, now completed: Explanation of the project: https://www.youtube.com/watch?v=inP0aEUCENw Video...

... idlers, creating a snug fit that reduces belt vibrations when the axes move. ... Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.1 Infill: 100 Notes: Post print trimming may be necessary to achieve evenly deep grooves.

Due to my limited access to hardware while deployed in the Middle East, I've tried to reuse as much existing hardware from the Anet A8 kit as possible. The extruder mount uses zip ties to secure the extruder motors and the 50mm fan is...

I mostly made a Frankenprinter out of Ben Levi's excellent MGN12 parts for Alu A8. Dont tell him, he will rip his hair out... The motor mounts are Straight from his collection. Anyway the parts work well for me. A tip: When mounting, tight everything...

I mostly made a Frankenprinter out of Ben Levi's excellent MGN12 parts for Alu A8. Dont tell him, he will rip his hair out... The motor mounts are Straight from his collection. Anyway the parts work well for me. A tip: When mounting, tight everything...

... hour prints. For my set up, ended up having the second extruder at (X-32.25, Y0). Might also adjust the rear anet_dual_x_carriage_v4 since my X-axis belt was rubbing and added some spacers for the rear Tronxy mount which isn't clear in the photos.

ADVISORY: This laser mount for Anet A8 is only possible if you have installed my modification. To set it up, connect the laser module to fan #2 connector. You can find several tutorials on YouTube that show how to use a laser module with a 3D...

WARNING: This laser mount for Anet A8 is only possible after installing my custom mod, available at https://www.thingiverse.com/thing:2355176. The laser module must be securely connected to the fan #2 connector. For detailed instructions on...

This is the laser mount specifically designed for Anet A8. You can easily find tutorials online; just search for them. The laser operates on a 5-volt DC power supply, so you'll need to connect it to a voltage regulator such as an LM7805 to provide...

I am building and printing the Anet A8 conversion from the conversion files by c1olli http://www.thingiverse.com/thing:2190694, but the edited motor mounts for the Z-Axis are not perfectly designed... also experiencing troubles with the print... I...

... the bed support, rotate it 45 degrees (cura + anet a8 settings work well). Follow the pictures for installation steps. For other parts, visit my collection at https://www.thingiverse.com/aRGiRob/collections/my-anet-a8 or check out my profile.

...2 m3x8 screws + 5 m3 nuts BOM, Bed support provided in two versions, with or without glass clamps (see https://www.thingiverse.com/thing:3237268) Bed support must be printed 45 degrees rotated (cura + anet a8) follow pictures for installation steps.

These are the custom parts reuired to convert an Anet A8 over to a prusa style hotend/extruder. - Motor mount with prusa style adjuster with endstop mount. ... - Z motor mounts that adjust the rod/threaad to the correct location (using the same top...

These are the custom parts reuired to convert an Anet A8 over to a prusa style hotend/extruder. Motor mount with prusa style adjuster with endstop mount. ... Z motor mounts that adjust the rod/threaad to the correct location (using the same top rod...

This is a Y Axis Leadscrew conversion for the popular Anet A8 3D Printer... The plan is to run a bearing-supported leadscrew with the Y axis motor mounted on the front. Parts: 4 x M4 x 16 mm - For Lead Screw Nut Holder to Carriage 2 x M5 x 25 mm -...

2 m3x8 screws + 5 m3 nuts BOM,Bed support provided in two versions, with or without glass clamps (see https://www.thingiverse.com/thing:3237268)Bed support must be printed 45 degrees rotated (cura + anet a8)follow pictures for installation steps.You...

Wanted to reduce the weight from the X axis on my Anet A8 Plus. Removing the weight of the stepper motor is a huge advantage. I accomplished this with this simple 2020 bowden stepper mount. It requires no supports and prints super quickly. Print with...

I needed to reduce the weight on my Anet A8 Plus from the X axis. Eliminating the weight of the stepper motor offered a significant advantage. I achieved this with a simple 2020 bowden stepper mount that requires no supports and prints extremely...

This is a comprehensive kit for transforming a standard ANET A8 into a bowden setup capable of printing flexible materials with ease. To make it work flawlessly, you will need to print all the included components yourself. Additionally, gather some...

Wanted to reduce the weight from the X axis on my Anet A8 Plus. Removing the weight of the stepper motor is a huge advantage. I accomplished this with this simple 2020 bowden stepper mount. It requires no supports and prints super quickly. ...Print with...

I wanted to reduce the weight from the X axis on my Anet A8 Plus. Removing the weight of the stepper motor is a significant advantage. I achieved this with this simple 2020 bowden stepper mount. It requires no supports and prints super quickly. Print...

Conversion to casings of the movement axis Y of the bed. Print out the number of parts listed (3 normal ones and one that makes contact at the endstop). The used casings are 11x22x8mm, four units. Videos in operation:...

Anet A6 Full Graphics Display Conversion Kit for Anet A8 Stock Mounting Position. This kit is specifically designed for relocating the original Anet A6 full graphics display to its stock mounting position on an Anet A8 printer. The idea behind this...

The Laser Exhaust Filter Consumes Fumes During Cutting + Installation on the LaseR Fan 33x33mm with Emissions Directed to the 3D Printer Anet A8 Ventilation System.

... 3D Printer into a fully functional low-power laser engraver! ...Detailed instructions can be found on http://lokspace.eu/anet-a8-3d-printer-laser-engraver-mod/. ... Print Settings: Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 100%