anet a8 lack enclosure 3d models

One Power Shell Front One Power Shell One Power Shell Back Optional components include: A 90mm fan (I used an old PC fan, which runs on 12V) Four M4 screws with a length of 16mm Four M4 nuts You may also want to consider adding: A power connector...

It's simple, yet effective, and I'm using it to mount the power supply outside of my LACK enclosure. The screw holes are precisely 3mm in size. I've also included a handy template for a quick print, just in case you want to use it for something...

Compact Power Solution: The Anet A8 Power Supply Enclosure Features a Convenient Side-Mounted On/Off Switch

Far from an IKEA store, I too had to get creative and make my own enclosure for my Anet A8 without relying on their touted "lack" of products. Now, I'd like to share this DIY project with you, so tell me, what do you need? To build it, you'll...

I was attempting to print ABS on my Anet A8, but ran into issues like layer separation and splitting. After researching online, I discovered that an enclosure is necessary to maintain a hot temperature. While browsing Thingiverse, I found some...

I created a straightforward enclosure for my ANET A8 using inexpensive PVC pipes with a 16mm inner diameter and 20mm outer diameter. To build the enclosure, I used Polyethylene sheets secured by double-sided adhesive tape. As a result, I can now...

Here are the 3D printed parts for my Anet A8 printer enclosure. The case features holes for connecting cables and mounting the power supply and motherboard underneath the printer. I've also included space to install an LED strip and a camera for...

Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.28 Infill: 5% Notes: Print without supports. You can print with even lower infill rate if you want, like 2-3%. Brim should not be required. ...How I Designed This I used Tinkercad...

I designed a custom enclosure to securely house my 24v to 12v converter for my Anet A8 Plus, enabling me to attach LED lights directly to the printer. However, the existing attachment points on the converter were flimsy plastic components that I...

Its precise design allows for reliable and efficient operation within the modified Anet A8 framework. To secure the necessary hardware components in place, the following screws will be used: Three M3 screws with a 19mm length provide robust support...

... It's designed for use with a 120mm fan. p.s. If you want to place the box next to your printer like I did, you'll need to extend some of your wires. Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 20%

I designed this enclosure around a multimeter I purchased on Amazon from https://www.amazon.com/gp/product/B01JOUZELG/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1, but it appears to be widely available at standard outlets. The meter comes with a 100A...

... table (available at thingiverse.com/thing:1843235). ... **Print Settings** * **Printer**: Anet A8 * **Rafts**: None needed * **Supports**: Not required * **Resolution**: Set at 0.2mm for optimal print quality * **Infill**: Optimized to 20% density

I'm Preparing for X Axis of Anet A8 Printer (Installed on IKEA Lack Table) I Used These Feet to Elevate the Ikea Lack Table So the Printer Could Fit Underneath - Check Out This Useful Thing at https://www.thingiverse.com/thing:1814763 And I Utilized...

The parts are all original from the Anet A8, only changing the 40-tooth extruder gear.\nI have also left a small lateral opening at the back for someone who needs to pass the motor cables horizontally, although in this setup it's natural for them to...

Frames of Anet A8 are extremely unstable and shake violently. I strongly believe that this pillar (simple screw jack) can significantly reduce frame vibration during printing. The minimum required height for stability is 60mm. Since I already have...

I designed this solution to resolve the Anet A8's issues related to Ikea's shortcomings. The frame no longer moves, thanks to my intervention. ...The total height has been adjusted to a precise 72 millimeters.

Coil holder for Ikea Lack table to be printed X2, Remix of the stl from cults3d.com, a tool made to reuse Anet parts, Install it securely to the table before loading a reel, All my prints are showcased on Instagram at instagram.com/aneton3d.

I remixed this because i couldn`t find any suitable table stacker systems for my Anet A8 printer. I raised the top and the bottom parts each to match 5 cm. Like this you get a total ammount of 10 cm in extra height to fit bigger printers like mine.

I remixed this because i couldn`t find any suitable table stacker systems for my Anet A8 printer. I raised the top and the bottom parts each to match 5 cm. Like this you get a total ammount of 10 cm in extra height to fit bigger printers like mine. ...

Printable spool holder for Ikea Lack table X2 Ensure the holder is securely fastened to the table before placing a spool on it All my prints are on my Instagram account: https://www.instagram.com/aneton3d/

Following up from my control board cooling fan cover, I needed a method to draw in cool air from outside the enclosure as I suspected there could be a high likelihood of the enclosure temperature rising significantly when printing with ABS. I also...

Following up from my previous control board cooling fan cover design (https://www.thingiverse.com/thing:3032480), I needed a solution to ensure cool air from outside the enclosure could be drawn in, as I figured there would be a high likelihood of...

The remix is now at a height that accommodates an Anet E12 printer.

I'm building an enclosure for my Anet A8, designed to house the factory mainboard and dual Simpzia Mosfets. I'll post updates as I work on it. Please note that this enclosure currently lacks holes for wires or airflow. ... The mockup includes two 40mm...

It's intended for installation beneath an Ikea Lack table, which serves as a secure enclosure. ...The included fan mount accommodates 120mm fans and can be used at your discretion; however, printing additional Support Mounts may be necessary to fully...

This innovative design empowers users to seamlessly integrate an 80MM PC fan, while simultaneously reorienting the main board from its standard position to provide effortless access to both the USB and SD card slot. For optimal results, M3 hardware...

To reduce the noise my printer makes I came up with this box. The box is 70cm x 50cm x 50cm big (inside) and is made from 6mm plywood. The front is made from some acrylic glass (approximately: 70cm x 50cm). At the side I glued some U-shaped aluminium...

This design was made to work with my Anet A8 electronics enclosure https://www.thingiverse.com/thing:3085130 and Leo_N's brackets https://www.thingiverse.com/thing:1872162 Print Settings Printer: Anet A8 Supports: YesResolution: 0.2 Infill: 30%...