anet a8 hot bed 3d models

This leveling tool should function smoothly on Anet A8 and Prusa-style printers, adapting easily to both sides - front and back - with a simple flip. To operate effectively, the screw heads on the bed must be accessible at all times. ...Remember to...

There are moments when I lack the energy in my fingers to turn the Anet A6/A8 Bed Level Thumbwheels by hand. To overcome this challenge, I turned to a clever upgrade designed by Area51, which can be found on Thingiverse at...

... if you have a sensor. ... Original screw from Anet A8 / A6. PLA is strongly discouraged, use ABS or other materials so that it does not deform with the heated bed. ... 12/15/17: Added 13mm 2.0 spacer (flange to prevent the piece from pivoting)

The Anet A8 and A6 Printer's Thumb Wheel Upgrade A bed level thumb wheel upgrade is available for the Anet A8 and A6 printers, offering improved precision and ease of use. This thumb wheel can be used in conjunction with the original wing nut that...

In my case, hotbed springs are fully compressed, so this part is 5mm instead 3mm, so springs are relaxed and not so serious hot bed bending problem. Notice in pictures I have installed crystal corners that compress springs 1mm aprox and centers in...

This is a revised version of the ArduCam Stand remix, available here: https://www.thingiverse.com/thing:1579435 I've replaced the existing foot with an Anet A8 bed mount, drawing inspiration from this design:...

Bed Level Knob for Anet A6 or A8. Made to Simplify Adjustment with Large Fingers. Also Handy with Glass Bed, No Need to Access Screws Underneath. Note that this requires drilling and removing threads from the H-shaped frame underneath. This process...

... on top, which can be adjusted by tightening or loosening it to regulate the bed height without needing to touch the screw. Printer Settings Printer Brand: RepRap Printer: Anet A8 Resolution: 1.0 Infill: 20% Notes: PLA at 195°C, bed temperature 60°C

This is a support bracket designed specifically for the Anet A8 heated bed, engineered to alleviate stress on solder joints where wires are directly soldered. It's particularly beneficial when using thick or stiff wires, as it helps mitigate strain...

I redesigned lord_alan's cable strain relief for Anet A8 heat bed, available here: https://www.thingiverse.com/thing:2474429. I adapted his original model in FreeCad, taking cues from the OpenSCAD design he created. My updated version incorporates a...

Made a quick custom Thumb Knob specifically designed for M3 Nylon Lock Nuts used in Anet A8 build plate assemblies. This innovation prevents the best from shifting height during periods of vibration, ensuring stability throughout. ...It's also...

"Lamda" bed mount for Logitech C270 and Anet A8 printer. Lamda cuz first layer, as is, is a big greek lamda on printer bed :) Works well. Firm clamps. Enouch rear space is required, depends on where you want the camera height and backward offset...

So, I found the part here on Thingiverse (file `A8-0009.stl` in **[Anet A8 Acrylic Frame](https://www.thingiverse.com/thing:2288314)**) but it had different mounting hole layouts, so I created another one from scratch and made it 3D printable for...

The updated file is labeled Anet A8 Plus Bed Cable v4.stl. It was confusing that the table's cable was messy. I had two options: a simple or complex design. I chose to connect my chain to version 1874802 on Thingiverse. I again modified the...

This is a holder for the 3mm glass on a 3mm Anet A8 heated bed. I extended the side walls to ensure they stick about 0.2mm above the glass and added holes for a 3mm screw. Although the holders fit snugly, additional support is required. The screws...

For those with 12mm inductive sensors, refer to Thingiverse's design: http://www.thingiverse.com/thing:1884118 Print Settings: Printer: Anet A8 Rafts: No supports are needed. Resolution: Set the resolution to 0.2 mm. Infill: Opt for a 20% infill...

Made for the original Anet A8 Auto Bed Leveling Sensor to fit on these Belt Holders: https://www.thingiverse.com/thing:1433295 which I used to upgrade to this Bowden Setup: https://www.thingiverse.com/thing:2099577 Works just like the original Anet...

Print Settings: Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: To ensure proper installation, the support screws must be threaded into the bearing holes (M4). ... Post-Printing: This design is specifically for capacitive...

You can find the CAD-file in the files section. There are many linear bearings variants here on thingiverse, and to give due credit I've copied the idea for the bushing from https://www.thingiverse.com/thing:2537701 Unfortunately I couldn't get the...

One of these linear bearings replaces two LM8UU bearings for the Anet A6 or Anet A8 bed, effectively eliminating noise, mechanical play, and weight. It consists of just two parts: a housing and a snap-in spiral bushing. Self-threaded M4 holes allow...

The design is tailored to fit an Anet A8 (220x220), but any bed or glass that gets close to the edge should work just fine. To secure everything, tighten the screws until the spacer can barely move under pressure. Then, make some adjustments for a...

This is a GoPro mount designed specifically for the Anet A8 or AM8 3D printer's heated bed, but it may also fit other printers with similar dimensions. The thickness of my heated bed combined with a buildtac sheet measures 3.5mm, so this mount was...

The carriage also supports a variety of heated bed sizes: 220mm x 220mm (original A8 size), 300mm x 300mm (A8 Plus size) and 310mm x 310mm (CR10 size and hole spacings). I have included the .STP and .F3D files along with the .STL to enable you to...

I've noticed an increasing number of complaints about fried hotbed connections within the Anet community, so I decided to snag his design to remix for the A8 because I'm not a fan of the chunky and ugly chain. Please use filament that can withstand...

This a remix of Anet A6/A8 Bed Level Thumbwheel Upgrade by Area51https://www.thingiverse.com/thing:2350276/remixesAll the main details are on his bed leveling setup. So you would need to print 4 of each.The thicker 5.5mm thumbwheel is for M3 Nylock...

I probably ought to replace the bed power wiring with silicone-insulated wires.) These spacers replace the springs and thumbwheels and convert your A8 from an adjustable bed to a fixed bed. You'll probably want to at least enable manual bed leveling...

I probably ought to replace the bed power wiring with silicone-insulated wires.) These spacers replace the springs and thumbwheels and convert your A8 from an adjustable bed to a fixed bed. You'll probably want to at least enable manual bed leveling...

The ANET A8 Plus is an entry level printer and its smaller predecessor, the A8, had been based on the Prusa i3 machines. The A8 plus adds volume with a build size of 300mm x 300mm x 350mm which is quite generous considering the low cost of this...

I recently upgraded my Anet A8 with an auto bed leveler and a 5 mm plate attached between the part cooling fan and the extruder. This upgrade eliminated the possibility of using my old fan shroud, as the heating block would melt its top surface. To...

... 3mm machine screws to keep everything tight and precise. If you want to replicate my setup, you'll need to print the arm and three spacers. Here are the print settings I used: Printer: ANET A8 Rafts: No Supports: No Resolution: 0.2mm Infill: 50%