anet a8 hot bed 3d models

Probe Offsets * X_PROBE_OFFSET_FROM_EXTRUDER 55 // offset: left -right [of the nozzle] * Y_PROBE_OFFSET_FROM_EXTRUDER -62 // offset: front -behind [the nozzle] * Z_PROBE_OFFSET_FROM_EXTRUDER 0 // offset: below -above [the nozzle] Probing Boundaries...

My trick for simplifying bed leveling is this: the spacers are 15mm when stacked, so tighten all four screws until they just touch each other. Then, use the knobs to fine-tune the adjustment from there. This ensures that even if all four corners are...

I printed the parts for the Hypercube using the hypercube calculator tool from this link: http://superjamie.github.io/hypercube/ and I realized after cutting the extrusion profiles that the provided bed clamps of tech2C did not work. They were too...

My Y chain is situated on the right, prompting me to mirror and upgrade this chain protector found here - https://www.thingiverse.com/thing:2221564 - so it fits perfectly on the right-hand side of the bed.

For installation, start by unplugging the bed from its power source. Release the stem levers, then disconnect the belt from the stepper motor. Lift the bed and remove the old components by unscrewing them. Next, screw in the new pieces, followed by...

I remixed this design for a bed-mounted camera stand I found, and the original creation by papinist had one major flaw - it would sometimes catch on the frame, causing the belts to skip steps and resulting in print failures. To address this issue, I...

I needed a slim bed level knob of decent diameter for my bed. Here it is. ...For M3 hexnut, 8mm slim knob</p> <h3>Print Settings</h3> <p><strong>Printer:</strong></p> <p>PKM 8</p> <p class="detail-setting rafts"><strong>Rafts: </strong>...

I designed my Y chain to be on the right, so I mirrored this chain protector to match the right side of the bed: https://www.thingiverse.com/thing:2221564. ...The result wasn't perfect for me, so I tweaked the design a bit and came up with something...

Just try to create a better support system for the bed and cables. If you need any files, just ask! Original project: https://www.thingiverse.com/thing:1875869 This thing was made with Tinkercad. ...Edit it online at...

For expansion, you will need: 1 aluminium plate with a thickness of 0.4mm and dimensions of 310mm by 260mm 1 aluminium plate with a thickness of 0.4mm and dimensions of 260mm by 30mm 2 aluminium plates with a thickness of 0.4mm and dimensions of...

To ensure a secure grip, I also extended the bed mount's legs, resulting in improved stability and a more reliable setup. ...I'd like to extend my gratitude to the original designer of the tilt mount for their innovative design that served as the...

Initially, I was thrilled with my design until it kept breaking and getting tangled in my heated bed. That's when I discovered the spring-loaded concept by MaddeMichael, which I incorporated into my own design along with a unique mount location. To...

The general idea is from LucaCap's rear bed leveling sensor holder (http://www.thingiverse.com/thing:1883473). All credit for the fantastic design and idea goes to him! Nevertheless, the original design requires tapping threads into the metal...

With larger knobs you can have better control of the rotation of the tensioning screws for the leveling of the hot bed of the 3d printer, besides adding some spacing guides for the springs that manage to stabilize them and improve the compression in...

I recently acquired a BigTreeTech ZSYong 2in1out hot end and encountered an issue finding compatible x carriages for my Anet A8 printer. I decided to open Fusion 360 and design my own solution. I utilized ABS material with a skirt at approximately...

---------------------------------------------------SUCCESS----------------------------------------------- \r\n\r\nI'M SHARING THIS POST TO LET ANET A8 USERS KNOW THAT CENTERING AN OBJECT WITH E3D NOZZLE IS POSSIBLE WITH THE OFFICIAL ANET A8L FIRMWARE...

This remix is due to the belt tensioner tendency to down tilt on tension. The goal was to have a more linear tension without tilting braces. It remix the longer belt tensioner in the remixed list. Also include 3D models to check proportions...

This is a precise adjustment unit.

This thumbwheel is simple to turn, and does not collide with the frame. It has a hole for an M3 nut and screw. Print 4 pieces. Use self-locking nuts if available. It can be used together with my spring holder, but it's not strictly necessary:...

This component is specifically designed to safeguard the belt and will be securely attached to the rod guiding the spring of the heating chamber.

I'm aware that others exist, but I encountered an issue with the previous one I printed - it was too large and hit the front of the frame. These spacers match the size of a wing nut, albeit slightly taller due to the bottom layer. They work well...

This Remix Offers a Deeper Inner Experience for the Adventurous Type The accompanying Fusion 360 file has been provided for further exploration. ... Update: The files have been corrected and are now ready to use.

This belt holder design comes from here : https://www.thingiverse.com/thing:4221683 The Scad code has been highly revisited and tided up. what is parametric: - base plate size [x,y,z] - holder plate size [x,y,z] - holes size [diameter]...

A Mitutoyo No2046F requires an M6 x 30 bolt to function properly.

I'm excited to share a straightforward solution that keeps the glass steady and level. This is my first time creating something, but it seems to work well on my system. If this helps you, let me know! ...I've also created a smaller version for those who...

I reworked the initial component because its holding area was too small for my glass slide, and simultaneously eliminated the label.

I widened holes to use the Anet A8 X Belt holder and tensionner by Miranina (cuz I like it): https://www.thingiverse.com/thing:2425783 This is made just like the original for E3D V6 and V6Lite, and Clones. I suggest you test assemble everything to...

I've been craving a custom fan cover for ages and I'm absolutely wild about Crash Bandicoot, so I combined them both! The Aku-aku is remixed from https://www.thingiverse.com/thing:1451494 There are two small supports for overhangs next to the eyes...

Metal cable chain holder designed specifically for larger space between holes on metal bed frame for better heat circulation.

for Anet A8