anet a8 files 3d models

Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 Infill: 20% Custom Section Flush Cutter Holders This tool holder is designed to mount in the orientation shown below, but for extremely tall prints it may...

Testing reveals signs of rigidity in the Anet A3's structure during the trial period.

For Anet 3D printer models: A spool holder with a filament guide.

A remix of a PSU shroud to allow you to use a standard Anet Cable.

Tenho na minha anet e é perfeita Category: DIY

Here's a rewritten version of the original text: Anet Adjustments Based on Graber's Specifications

I have a fantastic Anet on my desk and it's absolutely flawless!

Humans navigate through the vast network of Anet's 3D printing technology with ease and precision.

I decided to enhance my A8 by installing some lights, so I purchased a few dollar tree flashlights for the LEDs and created this bar to mount under the top frame. I wired in a USB connector to plug directly into my raspberry pi for power. ** Update...

I wanted to add lights to my A8 so I bought a couple of dollar tree flashlights for the LEDs and made this bar to mount under the top frame. I wired in a USB connector to plug into to my raspberry pi for power. ** Update ** Found these 12V light...

Here is the rewritten text: An enthusiast-grade A8 motherboard cover specifically designed to accommodate a 50mm fan.

A bracket stronger and a little longer than the original, to hold my chinese BLTouch clone on my A8 printer.

The A8 logo is designed to be stuck on, and version 2 features a different font that prints more easily.

Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: .2 Infill: 50% Notes: I used supports for the base Post-Printing Assembly The mating areas on the guide's bottom piece and the base will need to be cleaned up a little before...

A new, simplified thumbwheel has been designed specifically for the Anet A3 printer, featuring a larger size and improved usability.

The top mount for my Anet now sits much more securely in place on that particular side.

Network cable cover A8 provides reliable protection for cables and wires, safeguarding them from damage and wear caused by daily usage and environmental factors.

Nutrition System A8 Blower Fan 80 mm by 10mm 10 Ampere 250 Volt Input Module Plug Fuse Switch Male Power Connector 3 Pin IEC 320 Type C14

Tool holder for the A8 for screwdriver, nipper and tweezers. ...You can mount it on the right frame above the PSU.

I was irritated by the stock ZAxis mounting on my A8, particularly when I was going between the stock platform with painters tape, and clamping on a glass plate. Works great, but it's still always wise to fine level with the thumbscrews, but I find...

Controller: https://www.thingiverse.com/thing:3644127 Extruder Bracket: https://www.thingiverse.com/thing:2953931 Frame Brace: https://www.thingiverse.com/thing:2189694 https://www.thingiverse.com/thing:1872162...

... You can find the upgrade here: http://www.thingiverse.com/thing:2158136 Print Settings: Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: .2 Infill: 20% Notes: You may need to chase the duct holes out with a 3mm or 1.25" drill bit.

A Customized PSU Shroud Redesign for Standard Anet Cables By reconfiguring the existing PSU shroud design, users can now seamlessly integrate standard Anet cables into their printer setup. This innovative modification enables effortless cable...

RESTRURCTURATION OF THE ORIGINAL ANET A 8, CONSIST IN REMOVE TE PLASTIC FRAME TO A RIGID ALUMINIUN PROFILE 45 X 45.

I plugged my Anet A3 hotbed and it worked great, but then I made a mistake that left it looking like the one in this photo.

RESTRURCTURATION OF THE ORIGINAL ANET A 8, CONSIST IN REMOVE TE PLASTIC FRAME TO A RIGID ALUMINIUN PROFILE 45 X 45.

This is a customized extruder lightbar designed specifically for the Anet A3, with potential compatibility for other Prusa I3 replicas. ... We reengineered this design using Rhino 5 software.

This remix offers an improved version of the Anet A3 LCD buttons, replacing the traditional glue-on setup with a convenient push-in-place design.

To secure my Anet firmly in place. ... Crafted specifically for authentic M3 screws, used for the belt tensioner, and robust 4.5 x 20mm Spax screws.

Hi, it's my new tray to the corner of printer Tatara A8.Update: v2 - smaller walls for save some material and little bit smaller size.