anet a8 extruder replacement 3d models

After scouring the market for a suitable extruder mount and being dissatisfied with what was available, I took matters into my own hands and drew one from scratch. I adapted the fan mount and shroud from RoBo3D's E3D Cyclops or Chimera X Carriage...

I am experimenting with a custom heat-break that doesn't reach all the way to the top of the cold side of the extruder, requiring me to attach a tube to the bottom of the original part to fill the gap left over. This modification allows me to print...

This is my design for simple access (visual inspection) to the extruder. I tested several other solutions here on thingiverse but was unimpressed by each one. I believe it's a bad idea to have the heatsink not attached securely to the block and...

3) Insert the smaller Philips screwdriver that came with the printer between the fan blades to secure the screw mentioned in step (1) to the lower-left mounting hole on the extruder motor. 4) Secure the lower-right fan hole to the lower-right...

Extrusion conversion from Anet A8 and A8 Plus to Bond Tech "BMG"

Extrusion conversion from Anet A8 and A8 Plus to Bond Tech "BMG"

Extruder BMG holder for Anet A8/AM8

This is a small improvement for the extruder that comes standard on the Anet A8 printer, allowing you to adjust the thrust force of the extruder. Simply replace the spring with one that's smaller but just as strong, and place a 3mm nut on the lower...

Mounting a 50mm Fan on the Anet A8 Plus Extruder.

Practical Device for Simplifying Cable Management at the Anet A8's Extruder System. ... A Simple yet Effective Solution to Reduce Tension on the Cables Attached to the Anet A8's Extruder Component.

Designed a custom carriage for the A8 Anet printer to securely transport the Prusa MK2S extruder with precision and ease.

Printed on durable PETG material. It's possible that someone has created a similar design before now. ...I'm thoroughly pleased with my decision to print this item, and my thumb is definitely appreciative of the extra support it provides.

I enlarged the holes on the back plate to accommodate the linear bearing.

I redesigned the original button to fit my needs, scaling it down using Blender after taking precise measurements of my screwhead with vernier calipers. ...I chose to print it in TPU because its soft texture would be ideal for a user-friendly interface...

I made this design from one a friend modified first. I'll link back to the original once I find it again. I print a lot of flexible filament (TPU) and wanted to simplify loading as well as guiding all the way through. I added a short PTFE tube to...

I reengineered Orseeny J's Anet A8 Dual Extruder mount for Bowden to accommodate a third extruder. ...This modification is particularly useful for upgrading to diamond hotends.

 When I had the SV06 extruder in my hand, I could see clearly how the filament release lever was not going to work within that confined space of the steel carriage, so I started experimenting with carriage designs that would orient the SV06 extruder...

The Anet A8 boasts an upgraded twin extruder assembly, featuring the renowned E3D V6 hot end for enhanced printing capabilities and precision.

For those of you who swapped out your bowden extruder for the Anet A8 and have a top spool holder: I use this one: https://www.thingiverse.com/thing:2832620. Make sure that if you don't use this spoolholder, the bars around the Anet A8 frame must...

I required replacement bolting plates that fit at the base of the original Anet A8 spool holder, so here they are. ... Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: No Infill: solid Notes: I made them solid, feel free to infill if you...

Prusa I3 MK3S extruder carrier suitable for Anet A8 printers. Prusa's original is 1mm smaller to fit Anet's bar spacing. However, this modified the rear of the extruder to match Anet's rod spacing. ... We recommend printing body parts in PETG or ABS.

After printing the Anet A8 Extruder Button from Dryas, I found out that the screw of my extruder has a diameter of 6.7mm. ...So I took his design and reduced the inner diameter to the appropriate size.

----------------------------------------------------- Check out all my Anet A8 projects: - Anet A8 Prusa i3 Simple filament guide (Horizontal) http://www.thingiverse.com/thing:1764285 - Anet A8 RPi Camera Bed mount...

To use the Bear Extruder parts on A8 plus and keep your Z motor/rod mounts and all Y axis mounts. These X ends have the correct Z rod spacing for Anet A8 Plus. ... Bear Extruder https://www.thingiverse.com/thing:4362586 Bear Extruder Bltouch...

Updated beefy extruder button for Anet A8. The logo has been added and the filament slot is wider than the original, which was a bit too tight. I just tested it and it fits perfectly now. Enjoy! Print Settings: Printer: Anet A8 Rafts: No Supports:...

Hey, I created this "pipe guide" for my Anet A8 which has a cable chain on the X-axis because my filament keeps getting stuck in those chain pieces sometimes. ...Maybe it will help you too. It's designed for the stock extruder of the Anet A8.

BMG direct extruder with V6 Hotend or clones for the Anet A8 / AM8 or Prusa i3. X Belt Holder by kennethjiang, slightly changed https://www.thingiverse.com/thing:1666094 v6 Hotend Fan Shroud and 5015 + 40 Fang Combo by JamesK...

My extruder button is oversized compared to others, making it incompatible with standard buttons designed for the Anet A8. ...To resolve this issue, I simply enlarged the hole using Tinkercad.

Easy 3D printer extruder mount assembly designed specifically for the ANET A8 model, featuring 30mm, 40mm, and 60mm fan mounting options, as well as a dedicated spot for laser module attachment reference XR-LY06.

I support the Titan extruder on the upper right side of my Anet A8. ...I position the motor forward so that the bottom wheel doesn't touch the chassis.