anet a8 extruder fan hinge 3d models

2x M3*18 for the extruder 2x M3*20 and 2x M3 nuts for the hinge, fan, and heatsink 2x M3*18 for the duct fan and stationary hinge Credit is given to the original creators: https://www.thingiverse.com/thing:2290361...

I've been getting annoyed with having to take apart the extruder setup every time I've wanted to change the filament so I decided I would try and make a hinge to allow the fan to easily swivel up out the way. I am currently using a 40x40x20Mm fan to...

The hinge mechanism has been designed with a slot that allows easy removal of the fan power cable. To secure the mount in place, at least two holes are required - one above and one below the slot. The fan then fixes the mount into position. ...For...

I believe it's a bad idea to have the heatsink not attached securely to the block and since almost all the time I only need a visual guide to see if the filament is entering the correct hole I created this hinge that makes it incredibly easy to...

If I have time later maybe I'll update the Spriya fan to have the matching locking tab. The extruder fan/heatsink spacer by AZDawg. Hardware used: Hinge is a M3x45mm pan head screw, with an M3 washer between the head and the printed part and held...

* Extruder fan cover uses 2 M3x30mm flathead screws (had to counter sink on inside of heat sink) with 2 M3 locknuts. Would be better with M3x35mm screws to fit all the way in the locknuts but I don't have convenient access to these. * Extruder heat...

2x M318 screws for the extruder 2x M320 and 2x M3 nuts for hinges, fans, and heatsinks 2x M3*18 screws for duct fans and stationary hinges. Sensors are 18mm in diameter. Upgrade added on May 14, 2018: The inside size of the ring was enlarged to...

In my case, the bundle heat sink on Anet A8 is strongly attached to the extruder, which causes temperature fluctuations. ... //Bolt required// Fan fastening bolt: M3 x 20, 2EA Hinges shaft and screw: M3 x 15, 1EA + Heat sink fixing screws: M3 x 25, 2EA...

... so I decided it was time to add some extra reinforcement for the third attempt.\r\n\r\nI printed this model using black PETG with 70% infill and a 0.28 layer height. ...Supports are essential; orientate it with the fan holder flat against the bed.

I Designed this shroud to fit perfectly onto the Anet A8 Fan Hinge V2, created by the talented AShifter on Thingiverse at https://www.thingiverse.com/thing:2696721. This upgrade simplifies the look and expertly directs cool air exactly where it's...

Auto-Level Sensor Cover that Doubles as an Extruder Fan Cover: A Must-Have for Your 3D Printer. You Will Need the Following Components: 1. M3 x 35mm Hex Cap Screw with Nut 2. M3 x 20 Hex Cap Screws (Quantity of Two) 3. M3 x 18 Flat Head Screws...

I'm excited to share my design for the extruder fan hinge on the Anet A8. To make it even more functional, I've cleverly incorporated an end-stop-switch to detect runout filament. ...Furthermore, a versatile tool holder has been added, allowing for easy...

To simplify access to the extruder, just lift the fan. A tip and die set plus drilling are required. The sensor support for the right side can be found here: http://www.thingiverse.com/thing:1911146. Be cautious when drilling the fan. ...If you're up...

To simplify access to the extruder, the fan can be elevated. A tip and die set plus drilling are required. The sensor support for the right side can be found at http://www.thingiverse.com/thing:1911146. Be cautious when drilling the fan. ... If you...

I'm Remixed a 3D Printed Customizable Robot Arm by Thingiverse User "Robot_Arm". This DIY project is a great example of how to create a functional and versatile robotic arm using open-source designs and 3D printing technology. The robot arm features...

Please Report If the Anet A8 Extruder Fan Hinge Cover Is Not Working Properly.

This is a remix of hadoko's Anet A8 Extruder Fan Modification V2 See thing for more details: https://www.thingiverse.com/thing:2290361 Alterations: This part was completely remade but uses the same working principles as the original, notable design...

I was extremely dissatisfied with the original extruder setup on my Anet A8. Every time the filament became lodged or broke within the extruder, I had to disassemble the entire part. This was particularly frustrating because the screws for the fan...

I designed this thing because I want to put my fan on a hinge for an easy filament change without forgetting dissipation. It is compatible with cut heatsinks. Mounted over the heatsink, not between them, so the heatsink works correctly. The design...

User Requests Simplified Access to Extruder Gear Components

I designed this Thing to make it easy to access the extruder of the Anet a8 Printer when it gets jammed. Changing filament is also super easy, because you can actually see if the material fits the hole. You will need: -1x M4 metric screw (min 20mm)...

I remixed bartoaster's Anet A8 Fan Hinge to give it just a little more strength. I added a bushing for the screw attaching the hinge to the extruder carriage to prevent the screw from loosening while closing the hinge. The reason I wanted to hinge...

This is my rework of bartoaster's Anet A8 Fan Hinge. I genuinely enjoyed this modification, however, it failed consistently, breaking at the neck every time. ...Therefore, my revised version simply strengthens the connection between the hinge...

Remove the part after thehook because when homing that part hit the Z-Axis rode and block the fan hinge for oppening.Recommand to print in PETG for more toughtness, in PLA we have risk to broke the arm when openning many time for maintenance.

Bartoaster's version works effectively but has a fragile connection between the carriage and fan, posing a significant risk of damage. To overcome this, I reinforced the design with additional plastic, significantly increasing its durability. ...This...

This upgrade replaces the original wire on an Anet A8 Extruder Fan Cover, which comes equipped directly from the manufacturer of the printer itself.

I upgraded the ANET A8 PLUS Extruder Fan component today. I made significant changes to the extruder assembly. ...By replacing the cumbersome bolt with an accessible design, I greatly improved the overall user experience.

This is a filament guide and vent fan holder for the Anet A8.

The Anet A8 Extruder Fan Remover is designed with one goal in mind: effortless removal of the extruder fan for rapid access to the barrel. With this tool, you can swiftly take apart your printer's components without hassle. ...The remover features four...

I'm excited to share this fan shroud design with you all, which replaces the traditional metal guard on the extruder fan of my Anet A8 printer. While it's specifically designed for the Anet A8, I believe it may also work well with other printers as...