anet a8 e3d

See it run here: https://youtu.be/Nrn9100MQbY See my Rear Sensor Mount version here https://www.thingiverse.com/thing:2763157 All instructions are for the Anet A8. Reduced some sizes, moved some things and cleaned it up. I added some zip tie holes...

E3D V6 direct drive by 3Displacement suitable for v-slot x axis

Simple remix that removes the mount for an inductive sensor and adds a mount for a BLTouch. Works with almost any i3 setup with bearing blocks. Link to the cooling fan setup: http://www.thingiverse.com/thing:1746358 This mount is featured in this...

I had a major issue with the E3D V6 clone Bowden System constantly clogging, so I decided to switch to the E3D V6 Direct Drive. However, since I already had the Bowden system mounted on an IKEA Lack table, I needed to come up with a new carriage...

... with supports attached directly from the build plate. For optimal performance, consider using an E3D V6 silicone sock unless opting to print the fan nozzle in ABS material. ... Proper printing orientation is essential to achieve the best results.

A major upgrade for any cube auto level sensor on an E3D carriage made by Toosha deserves credit. Thanks are in order to him. I had grown weary of printing multiple clamp versions (such as the v6e, v6f, v6h, and v6j) just to see which one worked...

The Bill of Materials (BOM) includes: * Genuine E3D V6 Universal 12V * PTFE Tubing (highly recommended Cap tubes) * Blower Fan (if using the cooling mount) Print settings for this remix are as follows: Printer: Prusa Mk2 Rafts: No Supports: No...

This is a modified remix I created because the original design was a bit too snug for use with E3D v6 clones, so I expanded the mounting hole for the hotend. I also lengthened the bearing mounting holes since my printers X-rod was a tad too close...

I just want to connect Daveposh's Anet A8 2017 version X cable chain with fine tune adjustment directly to the E3DV6_E3DHolder_with_Chain_V4 from Don1337's top-rated Anet A8 E3D V6 Bowden MODULAR X Carriage V4.

It is incredibly light, making it easy to access the nozzle at all times, and offers the possibility of using almost any blower duct fan available for the stock Anet A8. ... This remix features a carriage designed specifically for hotends with a total...

https://www.youtube.com/watch?v=clixTeZ3fJA - Corrected spacing for Anets smooth rods (46.3mm center to center - injection molded holders) - A huge Z offset was added to bring the assembly high enough for the E3D V6 without wasting z height,...

This is an 18mm inductive sensor mount designed specifically for the new E3D Hemera Hotend, which will be attached to a custom mount created by Thomas Sanladerer: https://www.prusaprinters.org/prints/12763-e3d-hemera-upgrade-for-the-anet-a8 You can...

This is an attempt to completely replace the stock carriage of the Anet A8, making it lighter and able to carry two E3D V6 hot ends while keeping the same screw placement as the original. To mount this on your Anet A8, you'll need: * 1 x X axis...

I was extremely disappointed with various available options for the Anet A8 back in the day and I desperately wanted a bowden extruder, so I discovered this: Modular E3D V6 mount (use the backplate from this one)...

Print Settings: Printer: ANET A8 Rafts: No Supports: No Resolution: 0.2 Infill: 40 Post-Printing: Quick Installation Guide This is a quick installation guide with some images for the basic steps. Step 1: After unmouting stock metal frame, screw...

This is a Remix of @CrazyD82's E3D V6 Bowden carriage:\r\nhttps://www.thingiverse.com/thing:2668564\r\n\r\nDon't forget to check out his original thing, as he upgrades the pieces from time to time and I'm likely to be following close behind with...

...... I share my E3D-V6 holder personal design. Verry easy to print, without supports. It is important to print parts in ABS or PETG. Fan Duct is designed to have the best air flow just pointing on the nozzle. ... Thnaks for your feebacks and good print !

I'm excited to share my E3D-V6 holder personal design. It's incredibly easy to print, with no supports required. When printing parts, it's crucial to use ABS or PETG materials. The fan duct is cleverly designed to optimize airflow directly onto the...

Ultra lightweight carriage for a titan extruder and an E3D V6 Hotend designed to deliver exceptional performance. Key Features: - Perfect weight distribution achieved by positioning the extruder stepper precisely alongside the rails. - Allows...

Required screws 2x M3 x30mm for the hotend, 4x M3 x20mm for the fan and the strap.

As I wanted to avoid bowden in my printer, I modified Don1337's design so it could be used as a direct extruder. The fan duct for the heatbreak I'm using is from IsmaelPR1's model. I'm also sharing the blender file here for anyone who wants it.

I created this remix using Onshape, as the original fan mount was too big for my printer. ...I also adjusted the gap between the hot end and the exhaust to get a better fit.

I upgraded my Anet A8 with an e3d v6 Bowden hotend and used the Carriage from dldesign(https://www.thingiverse.com/thing:2077676). I like clean cable setups, so I designed this little addon to the new hotend carriage to tidy up the cables. I glued...

I recently upgraded my Anet A8 with an E3D V6 Bowden Hotend and utilized the Carriage from dldesign at Thingiverse, where they share innovative designs. To keep my workspace organized, I created a small addon for the new hotend carriage to manage...

Anycubic i3 (not mega, Anet A8 clone) e3d v6 bowden conversion cartridge The Anycubic i3's screw arrangement is distinct from the Anet A8. To minimize modifications, I've made an adjustment to the screws. ... Enjoy your 3D printer modification.

The modified print cooling system enhances airflow by expanding its cross-sectional area, thereby improving air circulation around the product.

Mounting a 3D Touch or BLTouch is a straightforward process that requires attention to detail and a bit of technical know-how. Begin by locating the mount bracket on your printer's frame, typically found near the extruder. This bracket is designed...

This remix combines features from two popular designs on Thingiverse: the E3Dv6 hotend holder, as modified by "Thing One" (https://www.thingiverse.com/thing:2741029), and another design that adds a Y filament joiner holder...