anet a8 e3d

Thisi is modification for Anet A8/A8 Plus X Carriage for E3D V6, original direct drive extruder I made slots for nuts, improved heat dissipation from the hotend radiator, rounded the edges This is a replacement for the standard Anet A8/A8 Plus X...

This is a replacement for the standard Anet A8/A8 Plus X carriage for use with an E3D V6 hotend with no additional changes. It uses the original part cooling fan, direct drive extruder, and belt tensioner. The backplate matches the original, so some...

This is a 18mm probe holder for https://www.thingiverse.com/thing:3599905 Some real photos here: https://www.thingiverse.com/make:691389 I designed this really quick and ugly but it works.

This is an 18mm Probe Holder for a specific Thingiverse project, namely https://www.thingiverse.com/thing:3599905. Some genuine photos can be found here: https://www.thingiverse.com/make:691389. ...I came up with this design in no time and it's far from...

A huge shoutout goes to everyone who helped make this project possible by contributing to its original design! I'm thrilled to announce that we've just added a brand new mount for a 12mm proximity sensor, perfectly complemented by a sleek 63mm hot...

This modified version of thing:1620630 has been specifically designed for use with a bolt from the mount, positioned 1 mm higher than usual and flipped over on its head at a 180-degree angle in order to fit perfectly around the nozzle cables.

This is an updated version of the Fan Black Diamond Bowden to work with the scheme from https://www.thingiverse.com/thing:2668564. It worked on my printer as shown in photos. Note: It needs support only at the nozzle, at the air outlet for the...

This section is designed to assist with installing the larger 40mm Anet A8 stock fan on the E3D v6, replacing the original 22.7mm blue fan clip. ...By incorporating more airflow, you can effectively prevent the filament from becoming lodged in the...

I built the E3D V6 Minimal Extruder from Fernan_3d at https://www.thingiverse.com/thing:2446493, but I lacked an optical Endstop so I designed this to keep using the stock one on my ANet A8. V2: After a few weeks of using this extruder, I noticed a...

I'm using a direct drive setup on my A8 with stock extruder motor and parts cooling fan. The build is designed for fan nozzles intended for the stock extruder. I added a small post to attach one of the wire clips from the A8 kit for strain relief. So...

This remix of [my earlier E3D Chimera+ mount](https://www.thingiverse.com/thing:4182256) adds a module that allows you to turn one of the two extruders into a direct drive, while keeping the other as a Bowden. The module can be attached or removed in...

Because the filament is still passed through a short Bowden tube, the module will most likely still work with a genuine E3D Titan or a similar extruder, but this may put the tube at an angle and/or require a longer/shorter tube. Adjusting the offsets...

My goal was to make a J-head mount that's as light as possible and supports the popular "Spriya" - High Efficiency Anet A8 Fan Duct found at https://www.thingiverse.com/thing:2133328. I used the method from the original metal mount for attaching...

Screw duct from inside edge, closest to the hot end 3 x igus RJ4JP-01-08 polymer bearings or LM8UU linear bearings 1 x E3D V6 or V6 clone 1 x 30mm 12v Fan OR 40mm fan using this 1 x 4010 12v Blower Fan 1 x Bltouch or 3Dtouch sensor Assembly is pretty...

This Tronxy sensor or Anet stock sensor can be used. ...Firmware Configuration came from TNS Firmware configuration Due to the altered sensor position the following changes have to be done in the configuration.h file (search for the capitalized string...

Wanted a fan mount for my E3D V6 clone that's compatible with customizable carriages and the Mistral v2.1. You'll need 2x M3 x 20 (mount to carriage) and 4x M3 x 15 (mount the fan). This is for the E3D V6 "3DFreunde" clone from Amazon, which has a...

... My A8 plus is still not 100% calibrated, but I printed at 20mm/sec with a 0.12mm layer height on and just left it running overnight with some pretty good looking results. If you like this design, be sure to leave a comment and a like. Thank you!

Some of the parts for the E3D Titan Aero were taken from GaryK47's design. On July 31, 2017, I added a Z-Axis limit switch mount for those not using auto level. Double 40mm fan duct and 12mm BL Touch sensor mounts were also added. The sensor is...

I managed to find a way to align dual extruders in the y-direction, freeing up valuable space on the hotbed. One-piece designs often prove challenging without supports, and attempting to print with them results in a non-functional outcome. After...

UPDATE 11/14/2023 - I no longer own a RepRap Orig. Prusa i3 MK2, I printed the parts and upgraded it, I tested it and sold it, it was only built to be sold. Therefore I cannot really provide much info on it. Except that it worked well! I used screws...

I'm currently working on a Laser Mount Bracket that fits perfectly with the E3D bracket on my Anet A8. To attach a laser to my Anet A8, I first purchased a laser. However, this would mean constantly removing and reinstalling my hotend, which is...

I really loved using this extruder setup on my Anet A8. It performed flawlessly with PLA... the only issue is the clamp assembly covers a small part at the bottom of the heatsink causing me to experience heat creep with PETG. Belt tensioner...

I will make a version to use the normal E3D heatsink fan clip and standard mounting point for the part cooling fan in the future, let me know if you need this. Other parts I used: Belt holder: https://www.thingiverse.com/thing:2427494 Bearing...

The individual possesses a handheld device featuring an LED clip specifically designed for illuminating printed materials.

When I stashed my am8 just about anywhere, saving weight was key, so the inductive sensor got bumped off for a bl-touch instead. ...You might even need to use some washers between the sensor and its holder for mounting purposes.

Hemera conversion parts name: -E3D Hemera upgrade for the Anet A8 -a8-46mm-v1.stl It fits with all other parts parts this is mixed form. https://www.thingiverse.com/thing:2115095/files In addition one of the bearing mounting holes in the...

I'm unsure if this design will work with the original X Carriage from the Anet A8, as I no longer use that printer. To print this part, orient it upright and add supports only for the Fan End, similar to the picture below. ...To achieve this...

It´s a Lightweight design Modular, you can change parts not used, or add different parts With only one screw you can change the height of Fan Duct It´s clean, your nozzle will still be on your sight, you can see what´s really happening It´s easy to...

Why this is the best design? It's a lightweight design Modular, you can change parts not used, or add different parts With only one screw you can change the height of Fan Duct It's clean, your nozzle will still be on your sight, you can see what's...

<p>This version has been tweaked so the belt insertion slots are 0.2mm tighter to hold GT2 timing belts.</p>