anet a8 e3d

This is a custom motor mount specifically designed for steel-framed Tatara printers, and it will not fit the original Anet A8 printer that comes with aluminum or fiberglass frames.

... I was perplexed by the absence of a probe sensor mount on this carriage, so I promptly created one in under 5 minutes using 3D Builder. This makeshift solution performs adequately for now. I utilized the Bracket_part_2_6mm to attach my E3D clone.

Here's a complete redesign of my previous attempts at creating a dual E3D mount, with a focus on achieving the following design goals: 1) A modular design that allows for quick part exchange 2) An easier mechanism for height adjustment of the J-head...

To create a carriage that could accommodate dual nozzles while retaining the stock direct extruder's efficiency with flexible filament, I incorporated an E3D remote extruder for reduced weight. The z-probe sensors were positioned 18mm from the...

I remixed the Anet A8 E3D V6 Direct Mount by pheneeny to better suit my needs. I added a few holes for cable management - use them if you like. I widened some of the smaller holes so I could use other parts with this. I also shaved about a...

Update 27.05.2017: A corrected version of the Backplate with Belt holder in correct direction is now available, thanks to RehabMD. Additionally, a separate part for the small Belt Tensioner has been uploaded, in case the Case print fails. Update...

It's not experimental anymore, it's functional and for now I don't see a need to improve it further because it works extremely well. This design was created to be used with this carrier that functions very smoothly, better than IGUS and LM8UU...

I yanked the screw mounts off the Raspberry since they weren't required.

This is a revised adaptation of an existing Anet A8 mount for the E3D Hemera Hotend, originally designed by Thomas Sanladerer: https://www.prusaprinters.org/prints/12763-e3d-hemera-upgrade-for-the-anet-a8. ...The revised version has been fine-tuned to...

A Sturdy Anet A8 Mount for the 1.75 mm E3D Titan Aero Extruder. NEW: A version with the option to mount a sensor on the right side of the extruder, in front of the Aero fan. (no Y offset = better bed levelling). A mount for an 18 mm sensor is...

UPDATE 09/04/2019: Added Easier BL TOUCH V2 Mounting Support Hello, Here's a prototype to improve for a dual E3D V6 intended for Prusa i3 and Anet A8. The smooth rod carriage is: https://www.thingiverse.com/thing:1609892 Just attach my base to the...

Hello, Here's a prototype to improve for a dual E3D V6 intended for Prusa I3 and Anet A8. The smooth rod cart X side has: https://www.thingiverse.com/thing:1609892 Just screw my base onto the smooth part (maybe improve this point?). My base...

The printer's frame is modified to accommodate the Anet A8 and AM8, with a customized fit for their 46.3mm X rod spacing. To achieve proper alignment, the x offset is set at -28, while the y offset mirrors this adjustment at -28 as well. ...Note that...

So I opened meshmixer and slapped Teaching Tech's bondtech mount onto an anet a8 mount, and kept a mount for a bltouch. It works well for the most part. There is no mount for a blower, which is something I need to figure out. I had to use a zip...

... to try to keep them in place.) There was also a slight misalignment of the holes for the belt holder that has been fixed. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 0.2 mm Infill: 40% Category: 3D Printer Parts

... tidy and secure wire routing. Before printing the carriage, be sure to verify your timing belt orientation. My Anet A8 requires an upside-down belt orientation, unlike other designs that feature two bearings on the upper rod and one on the lower.

(With the original, I jammed some Blu-Tack down the holes with the nuts to try to keep them in place.) There was also a slight misalignment of the holes for the belt holder that has been fixed. Print Settings Printer Brand: Anet Printer: A8 Rafts:...

The original Anet A8 bearing mounting bolts are employed, while M3 nuts and bolts are utilized in all other cases. The specifications are as follows: 15mm x 12, 6mm x 4, 25mm x 4. Updates: ========= A 12mm inductive sensor mount has been added. How...

The hollow threaded rod that mounted the MK8 hot end to the lower part of the filament tension bracket is what you'll use to secure the stepper motor to the E3D hot end. Simply spin the E3D hot end until the motor securely attaches to the mount. ...This...

However, I wanted to have an open top for putting a filament mixer in a bowden line so I cut the top out while leaving the probe and fan mounts. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No Resolution: 150 Infill: 40...

... Your Boards Firmware. I Used TH3DUF U1.R2.A8 And Had To Adjust Home Offset, Probe Offset, And Define Custom Esteps. ... I Have More Information About Installing The Linear Rod Modification In This Thing: https://www.thingiverse.com/make:750896

Mounting Adapter for the E3D V6 Hotend. ...Compatible with Anet A8 3D Printers and other similar models.

This is a specially designed E3D or Lite support for the Anet A8, carefully crafted to ensure optimal print quality and performance.\r\n\r\nFor effortless cable management, consider integrating an Adapter to Cable Chain // Filaflex tensioner from...

Unfortunately, its original positioning proved to be a major flaw - the fan holder sits too high, inadvertently cooling the hot end rather than the filament emerging from the nozzle on my trusty Anet A8. To address this issue, I cleverly added...

This is my dual blower E3D/E3D V6 Clone extruder head for an Anet A8 Style Printer. I have included a BLTouch and an Inductive Sensor Mount. The Blower Cover MM is optional but I would appreciate it if you printed it and displayed it proudly. If you...

Reworked from these designs - http://www.thingiverse.com/thing:1633606, http://www.thingiverse.com/thing:815725, and http://www.thingiverse.com/thing:926794. ...I have this setup on my Anet A8, and it operates flawlessly.

In my adaptation of the upgrade plate, featuring the original fans and an 18mm capacitive sensor, I drew inspiration from various other projects. Unfortunately, there were errors in my previous design; I aimed to place the sensor at the lowest...

This is my updated upgrade plate, featuring the original fans and an 18mm capacitive sensor. It's based on a few other projects, but I made some critical mistakes in the previous version that needed correction. My goal was to position the sensor at...

... For my carriage, it fits perfectly, and the distances between the nozzle and bed are spot on. I use a remix carriage from Dousi (https://www.thingiverse.com/thing:2203912) because I have an E3d V6 direct drive with a Bowden-style setup.

Thisi is modification for [Anet A8/A8 Plus X Carriage for E3D V6, original direct drive extruder](https://www.thingiverse.com/thing:5215000) I made slots for nuts, improved heat dissipation from the hotend radiator, rounded the edges This is a...