anet a8 bowden extruder upgrade 3d models

This update grants unrestricted access to the extruder motor. Changing filaments has never been easier. Installation is straightforward, taking mere minutes to complete. ...Appreciation goes out to Thingiverse for making this design available at...

I designed this because loading the filament on the A8 is a pain. on the lever i put a small piece of Teflon tube. The heat break is mounted so that it is equal with the chamfer as you can see on the picture. Its not perfect but its better than...

Because of the small size of the extruder button, I advise using a Layer Height (quality) setting of 0.1mm and a print speed of 40 mm/s for optimal results. It's also smart to use a "skirt" as your build plate adhesion method. Don't be shy about...

I eventually came up with this idea, which consists of two parts and is designed specifically for standard Anet steppers. As usual, I used sintered bronze bushings throughout. I produced versions with 4 and 3 bushings, but since the rods aren't...

I designed a simple cap using Fusion360 that helps release the extruder gear when loading and unloading filament. It's especially useful when you struggle to get the filament to feed through properly. Without it, the hex head tends to dig in too...

... suit specific needs, like mine, where a rapid connector features an M5 thread, whereas the standard component has an M6 thread. ...The spring guide is integrated into this design. This customized part significantly enhances the extruder's performance.

I recently expanded upon the Extruder Fan Mod V2 by hadoko and printed the whole thing with carbon fiber. ...Removing the support structure requires a bit of finesse, but once it's done, you'll have a sleek addition to your 3D printer, smiling.

Extruder fan silencer mod, bolt on top of your 50mm radial fan to bring down DB. On my setup from 30cm away Without Silencer: 65DB With Silencer: 57DB Bolt mounts are wide enough for M4 and are 2mm thick. Print to the quality you require,...

This conversion grants unrestricted access to the extruder drive. The concept originated when I viewed the design of SentinelRX5. https://www.thingiverse.com/thing:1749614 Installation is straightforward and completed within minutes. The part was...

I added a piece to stabilize the slight rotation of the extruder motor around its locking screw during sudden changes in direction. ...This allowed me to reduce even more the remaining wobble I had after separating the X-axis from the infinite screws of...

ENG: This is a straightforward pushbutton for the extruder screw. It's painful to press without a button. <h1>ESP:</h1> Un simple botón de empuje para el tornillo del extrusor. ...Duele cuando no hay un botón para pulsar.

reposition of the extruder fan to allow visual access to hotend and filament.this thing adds an aluminium heatsink and moves extruder stock heatsink and fan 23mm far and 20mm right from extruder motor allowing for visual inspection of the extruder,it...

2x M3*18 for the extruder 2x M3*20 and 2x M3 nuts for the hinge, fan, and heatsink 2x M3*18 for the duct fan and stationary hinge Credit is given to the original creators: https://www.thingiverse.com/thing:2290361...

This setup enables easy placement of the extruder cable underneath the plate, eliminating interference with buttons or display and reducing the likelihood of snagging during printing operations. ...By routing the cable through a large hole in the upper...

Originally took inspiration from https://www.thingiverse.com/thing:2380825, but decided that I didn't like how it attached to the upper bolt as I have a cable clip located there, it was also very brittle in the arm so I redesigned it to allow the...

I created this modification because loading the filament onto my A8 printer has been a real hassle. To simplify the process, I've added a small piece of Teflon tube to the lever. The heat break is positioned so that it's perfectly aligned with the...

This is a custom cover for the extruder fan. I swapped out the standard 40mm fan with a Noctua 40mm fan to significantly reduce noise levels. The Noctua fans feature a unique brown color that clashes with my OCD sensibilities, so I crafted this...

You'll need four hands to properly reattach the fan / heat sink / extruder stepper motor. I've tried it with just one screw removed, but it was essentially the same frustrating experience. I've since searched for alternative solutions from others...

I've upgraded this LED mount to withstand the extreme temperatures generated by an E3D V6 hot end. The original design was prone to warping over time due to heat exposure. To address this issue, I increased the thickness of the LED bar, which makes...

I've got a Bowden setup on my Anet A8, and I'm using the standard spool holder off to one side of my printer. But I wasn't happy with how twisted and messy the filament line looked as it was pulled up to the extruder - it was a real eyesore. And to...

This is a revised design for the E3D Bowden mount, tailored to be compatible with the Anet A8. For more information on printing the fan duct, visit:...

This is a comprehensive kit for transforming a standard ANET A8 into a bowden setup capable of printing flexible materials with ease. To make it work flawlessly, you will need to print all the included components yourself. Additionally, gather some...

Subscribe Now!!!\r\nWatch This Video at https://youtu.be/V-q_PJ_qY5Y\r\n\r\nTop Upgrade Still Available!\r\nGet It Here: https://www.thingiverse.com/thing:2770619\r\n\r\nBearing Options:\r\nCheck Them Out on Amazon at http://amzn.eu/d2HUwX9

Anet A8 direct drive bowden filament guide prevents the carriage from pulling hard on the filament while moving away from a filament roll placed on one side for easy setup. To mount it, simply use one of the LCD screws provided. I purchased two...

This is a straightforward bowden motor mount for an Anet A8.\nAttaches to the top of the frame via two existing 3mm frame bolts, either left or right.\nThe other designs didn't seem sturdy enough with tabs to hold them securely in place or offered...

To prevent bowden tube setups from snagging the LCD screen ridge on high-z height prints, a simple wedge shape is designed for Anet A8 printers. The walls of this design are 2mm thick with a hole for a screw. ...Printing considerations suggest using a...

** Inspired by a lot of designs here, I designed a bowden mount for my Anet A8 printer. I build an enclosure and will place 2 printers one over another. So the filament has to be guided from under the table, not from above like in the normal...

Inspired by numerous creative designs within this community, I created a bespoke Bowden mount tailored to my Anet A8 printer. As part of an ambitious project, I'm building an enclosure that will house two printers in tandem, one atop the other. To...

This is a Design to Utilize a MGN12 Linear Rail for the Anet A8. Things You'll Need: * 400mm MGN12 linear rail * e3dv6 clone with a length of 63mm * 4 M3x8 screws to mount the printed part at the sled * 2 M3x30 screws to mount the hotend * 2 M3x25...

I'm excited to mount my extruder stepper on the back of my Anet A8 3D printer, I found the perfect spot! ... Print Settings: Rafts: Off the table Supports: Out of sight Resolution: Crisp at 0.2 millimeters Infill: Strong with 25% density