anet a8 bltouch 3d models

A bracket stronger and a little longer than the original, to hold my chinese BLTouch clone on my A8 printer.

- original model had a couple of issues so Cura slicer didn't slice it correctly So I decided to make a remix with a little bit changed dimensions and it fits perfectly for my Anet A8 now. Changed blocks in Configuration.h for Marlin 1.1.6 Enable...

I've designed a custom mount specifically for my stock Anet A8 printer, which I've modified by removing the hotend fan and heatsink. The extruder securing bolts hold everything securely in place. To withstand the heat from the heat block, I print...

This is a custom mount for the BLTouch (3D Touch, etc.) that securely holds it inside the extruder carriage. ... #define X_PROBE_OFFSET_FROM_EXTRUDER 30 // Adjust to align X probe with the nozzle #define Y_PROBE_OFFSET_FROM_EXTRUDER -16 // Fine-tune...

This is a simple BLTouch mount that goes on the right side of the extruder assembly on an Anet A8. ... My probe offsets ended up being {X,Y,Z} = {57.59, 1, -2.15} This should vary slightly depending on your setup

Expanded the initial opening to accommodate the BLTouch Smart's dimensions, ensuring a seamless installation process.

Rear Mount for BLtouch or 3D Touch Allows Slide Screws More Room. Two Options Exist: One with Countersink Screw Holes on Back Plate and Another with Slot on Rear of Probe Plate to Accommodate Half-Round Screws. The Back Plate Features a Recess for...

To adjust the correct height, I use the BLTouch_83_Spacer.stl file. ... Offsets for this sensor bracket are as follows: X_PROBE_OFFSET_FROM_EXTRUDER is set at +60 Y_PROBE_OFFSET_FROM_EXTRUDER is set at 0 The boundaries for probing where the probe can...

BL Touch auto bed leveling mount specifically designed for the stock ANET A8, requiring no heat brake or extruder cooling fan removal. This mounting system leaves the machine in its original configuration, while providing precise bed leveling...

... from https://www.thingiverse.com/thing:2191550. ...My new BLTouch didn't fit because its connector at the back had grown by 1mm, so I needed to trim it down to make it slide smoothly into the mount. ...Maybe someone will find this as useful as I do.

It's based on BLTouch Smart version. ... **Marlin parameters from original bracket (https://www.thingiverse.com/thing:2773637)** Offsets for this sensor bracket: X_PROBE_OFFSET_FROM_EXTRUDER +60 Y_PROBE_OFFSET_FROM_EXTRUDER 0 The boundaries for...

Bracket for holding a BLTouch sensor on a ANET A8 Plus printer.

Hello, This is my BLTOUCH support system specifically designed for Anet A8 printers, compatible with most of the thingiverse upgrades available today. To get started, you'll need to acquire a few essential components: Two 4x10 screws (Anet Origin...

However, when I upgraded to ABS, the heat from the extruder caused my PLA upgrades for the ANET A8 to warp. Additionally, the arm on the mount broke, making removal difficult due to a blocked mounting screw. To address these issues, I redesigned the...

I was looking for a mini 12864LCD mount for my Anet A8 but could only find variants which were separated from the printer. I don't have space for this with my setup. ... I designed this mount in Fusion 360 and it can be mounted to the original frame...

We're aiming for a compact design, just 12 millimeters tall.

This Part serves as a mounting platform for the BLTouch Sensor on Anet A8 Plus 3D printers. Due to design differences, the original Anet A8 model is not compatible with this mount. It's installed on the left side of the extruder, utilizing the same...

This design also works on the Anet A8 and other printers, with users reporting successful installations. The mount is easily installed behind the blower fan, requiring longer screws in some cases. I'm using Marlin RC-8 firmware, which can be...

Mounting the ANTCLABS BLTouch to the BQ Hephestos Prusa i3 is a breeze, and users have successfully adapted this design to work on their Anet A8 and other printers as well. To install, simply attach the mount behind the blower fan - you may need to...

Here is a support for an E3DV6 on an Anet A8 with a BLTouch. Offset X: -39 Offset Y: 19 This bracket mounts on slides using original screws (12 M4*7 screws). The nozzle is secured with two M4*40 screws and matching nuts. Install the nuts in the...

A minor tweak of the BL Touch Mount for the Anet A8 Plus is now available.\r\n\r\nThe original design was crafted by KDH832832, found on Thingiverse under #3547279.\r\n\r\nTo improve stability, the base has been thickened to prevent bending and...

This is the same as Anet A8 Plus BLTouch Sensor Mount by Nwpvr only with a 2mm hole going through it. I've printed a few hours with this and do not see the same sagging issue. This Part is a BLTouch Sensor Mount for Anet A8 Plus (not the original)...

Anet A8 BLTouch Mount - Right Side - Inline with Nozzle There are a lot of Anet A8 3D Touch mounts out there, but none met my needs. I wanted the probe on the right side and inline with the nozzle, not in front or behind it. I designed this one, and...

This is a BLTouch holder designed specifically for "Anet A8 E3D V6 Bowden MODULAR X Carriage V4 *BEST ONE*" to accommodate a TriangleLab Touch Sensor...

To use this sensor on an Anet A8, you either have to move to a different board, modify the LCD cabling (see http://www.thingiverse.com/thing:2091529), or free up a pin on the Anet board by converting the display to I2C. See my design for freeing up...

There are a lot of Anet A8 3D Touch mounts out there, but none met my needs. I wanted the probe on the right side and in line with the nozzle, not in front or behind it. I designed this one, and it's working well for me. I have used it for some...

Mount the bracket securely onto the right bearing by screwing it into place from the bottom. No adjustments are required for the existing screws. ...To offset the bracket on your Marlin system, input the following commands: set X to 58 units above zero...

This is my attempt to run Marlin 2.0 on my PKM8 (former Anet A8) with Anet3D V1.5 board using Atom, Clang, and GitHub. I won't make a tutorial. If you have no idea what's going on, go do your homework and figure out how to update a firmware. My...

This is a fresh take on my Anet A8 BLTouch Holder, designed for mounting directly in front of the extruder fan. ...This iteration has been precision-crafted to work seamlessly with the Hemera Extrusion system and Tom's Fan Mount Adapter, available at:...

This bracket secures a BLTouch on an ANET A8 stock hotend, integrating seamlessly with a belt holder for the X-axis - a stock configuration that's less than ideal. ...The combined unit positions the Bltouch precisely adjacent to the nozzle while...