anet a8 bl touch 3d models

Anet A8 BL Touch Mount A mount to hold a BL Touch Sensor to an Anet A8 I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then...

Anet A8 BL Touch Mount A mount to hold a BL Touch Sensor to an Anet A8 I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then...

... pocket to accommodate the BL Touch "Smart" V3.1. ...Allows for clearance of the wire connector on the sensor. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: Standard Infill: 15% Filament: Makerbot ABS Red Category: 3D Printer Parts

A mount to hold a BL Touch Sensor to an Anet A8I needed a mount that would hold a BL touch sensor to my stock Anet A8 carridge. This design works using the fan mounting holes on the front of the carridge (the fan is then screwed back in place over...

The design parameters for the sensor pocket are being revised to fit the BL Touch "Smart" V3.1, ensuring that there is adequate space around the wire connector for a smooth installation process.

I'm impressed by the innovative design on https://www.thingiverse.com/thing:2845069! I've taken it a step further by fine-tuning the holes that secure the BLTouch to perfectly center them from the edge. To ensure accurate probing, you'll need to...

Here is the rewritten text: Anet A8 Plus Printer: Installing the Bl-Touch Support System The Bl-Touch support system for the Anet A8 Plus printer is now available in beta version, and it's ready for testing. Positioning the Holder: To install the...

A compact version of the BLTouch rear mount is available, allowing for adjustment of sensor height using washers. This design places the sensor 12mm behind the nozzle, providing additional space for accurate measurement. ... #define...

A shorter version of the BLTouch rear mount. U can adjust the high for the sensor with washers. It is 12mm near to the nozzle for more space to measure. ... define X_PROBE_OFFSET_FROM_EXTRUDER 10 define Y_PROBE_OFFSET_FROM_EXTRUDER 41 my optimal...

This is a BL touch holder specifically designed for the Anet A8 Ultimate Direct E3D v6 & Titan Extruder Carriage With Chain by Thorinair. The offsets required are as follows: - X: -3 - Y: 33 To achieve optimal results, I recommend setting the...

This is a mount that allows the E3D Hemera extruder to be mounted to an ANET A8. It includes a BL Touch mount. I didn't design this, this was designed by Marcus Mendenhall. The openSCAD file is available on github and allows several configuration...

For long time i search Titan Aero mount for Anet with BL Touch, in one piece, easy to print, compact, good looking a most of all that will not cause losing of printer space, I tested may and did not found any that will suits this needs so i designed...

I've been searching for the perfect Titan Aero mount for my Anet with BL Touch for what feels like an eternity. I needed something that was not only compact but also easy to print, had a sleek design, and most importantly, wouldn't take up valuable...

For long time i search Titan Aero mount for Anet with BL Touch, in one piece, easy to print, compact, good looking a most of all that will not cause losing of printer space, I tested may and did not found any that will suits this needs so i designed...

When I stashed my am8 just about anywhere, saving weight was key, so the inductive sensor got bumped off for a bl-touch instead. ...You might even need to use some washers between the sensor and its holder for mounting purposes.

Rear Anet A8 X Belt with BL Touch Holder - a remix based on creations by zumili and matsondawson. The probe is positioned at the rear for a cleaner look, utilizing one M3 nylon nut as spacers. Several configurations need to be modified to make this...

Redisgned this BL-TOUCH mount as the original one bends after a few times messing whit the z-offset

My adaption for a bl touch holder, mounts off the custom backplate i made for Anet a8.

This is a mount for a BL Touch on an A8 Plus. I had found a number of alternative methods, but all looked a little flimsy with a large cantilever. This is Easy to print Easy to mount Strong Integrated cable management I have produced two versions:...

A Simple Mount for BLtouch Sensor and ANET A8 with Spacer for Screw Installation. I Employed M4 Screws and Cut Threads in the Bearings. I Fabricated the Entire Assembly from Aluminum, but You Should be Able to 3D Print It. ... The Provided SketchUp...

I'm printing a custom part for Anet A8 using an X belt holder design found on Thingiverse at https://www.thingiverse.com/thing:2134843. ... Support material is enabled with a resolution of 0.1 to 0.2 millimeters and infill set between 20% to 30%.

Fixed the BL_Touch mount available at: https://www.thingiverse.com/thing:4019350 Using Netfabb's online stl fixer

remixed this remix as the orig had errors in the stl shaved off the front and rear to make it look less bulky, raised the bl touch by 2mm for better clearance while printing offsets: define X_PROBE_OFFSET_FROM_EXTRUDER -28 define...

Shaved off the front and rear to make it look less bulky, raised the BL touch by 2mm for better clearance while printing. ... Offsets: Define X_PROBE_OFFSET_FROM_EXTRUDER -28 Define Y_PROBE_OFFSET_FROM_EXTRUDER -40 Define Z_PROBE_OFFSET_FROM_EXTRUDER 2 ...

This is a remix of Anet A8 E3D V6 Direct Mount by pheneeny & Anet A8 E3D V6 Direct Mount with BL Touch by frizinko. They have done an incredible job with both the designs, and I've strengthened their work since I faced issues with both originals. You...

... sind. Funktioniert perfekt mit dem BL-Touch ;-) Passender Fan Duct https://www.thingiverse.com/thing:4715946 Noch eine geänderte Version mit etwas tieferer Montage für den BL-Touch in verbindung mit der längeren Volcano Nozzle hinzugefügt.

... an additional vertical mount to secure the extruder motor, now held firmly in place by four screws. ...I also added a detachable BL Touch holder that can be easily mounted on the right-hand side as an alternative to its original position at the front.

die Befestigungsbohrungen so geändert, das diese von oben zu Schrauben sind. Funktioniert perfekt mit dem BL-Touch ;-) Passender Fan Duct https://www.thingiverse.com/thing:4715946 Noch eine geänderte Version mit etwas tieferer Montage für den...

Phenney provided two versions of this with his original thing, but I required the BLTouch to be elevated further still. This adjustment increases it by an additional 2mm. Upon modifying it, I seized the chance to position it a little closer to the...

Combined https://www.thingiverse.com/thing:2354864 and https://www.thingiverse.com/thing:2773637 so you can have a chain and the mount at the same time. Edit: Made some walls thicker as it had a tendency to snap. ... I printed mine in PLA - 100%...