anet a8 3d printer parts

RESTRURCTURATION OF THE ORIGINAL ANET A 8, CONSIST IN REMOVE TE PLASTIC FRAME TO A RIGID ALUMINIUN PROFILE 45 X 45.

RESTRURCTURATION OF THE ORIGINAL ANET A 8, CONSIST IN REMOVE TE PLASTIC FRAME TO A RIGID ALUMINIUN PROFILE 45 X 45.

I plugged my Anet A3 hotbed and it worked great, but then I made a mistake that left it looking like the one in this photo.

But on the other hand, I've gained a lot of experience in 3D construction and printer setup. After some testing and printing, I'm convinced that this case has improved my printer and printing results. There are no cold spots on the heated bed, which...

Modified Version of the Original Filament Guide Specifically Designed for the Anet A8 Plus 3D Printer

This is an uncomplicated, articulated wire guide designed specifically for use on Anet A8 3D printers.

A DIY Solution to Store Your Anet A8 3D Printer's Filament: The Essential Spool Holder

Craft an appealing 3D-printed casing specifically designed for showcasing your Anet A8 printer

To upgrade your 3D printer, you'll need the part from Thingiverse (https://www.thingiverse.com/thing:2445884) and another one. Before using the purge bucket, it's recommended to apply tape on the part to prevent smelting. You can see a picture of...

Follow these steps to ensure your filament feeds smoothly and avoids getting jammed: place the filament onto the top of the print bed, making sure it fits snugly in its designated slot within the A8-frame assembly.

Modified from numerous others to suit the dimensions and wiring of my printer, I utilized an A8 Desktop 3D Printer Prusa i3 as advertised at http://www.gearbest.com/3d-printers-3d-printer-kits/pp_337314.html. I hope it proves helpful for those who...

I recently upgraded my ARNET A8 with an external MOSFET for the heat sink. ...This also required a mounting bracket.

As I still use my spool at the same level as my 3D printer, I observed that the filament was under constraints. I decided to design my own filament holder in order to reduce those constraints. I know it would be much better to put the spool at a...

Here's what you'll need: * 35 x 35 timber (3m long, possibly longer due to cuts) * Miter saw * Wood screws * L Brackets x 8 * T brackets x 4 * Rubber feet x 4 Printed parts, no supports: * 0.2 res * 65% infill After assembly, you'll need to adjust...

Required materials include: * 2x 608ZZ ball bearings * 4x M3x30mm bolts * 4x M3 nuts * 8x M3 washers (optional) To print the necessary pieces, you will need to print the following: * 2x Side Plate * 2x Pulley Shaft (omit this if printing V2) * For...

I recreated this from Snoekieboe's original concept, and I really liked his idea after building an external screen enclosure to fill the gap on my Anet board. ...I simply reworded it myself.

I've created my own level rings for the Anet A3. I just wanted some that would make leveling easier. ...Simply press down on the nut and screw it from below.

Request changed to use M5 screws with T bolts for fixation on the 20x20 frame, and in addition, the Anet Evo logo was removed and the tubes where the screws enter were reinforced.

... holder designed based on Thingiverse's reference model 2729772, tailored to accommodate PH1 and PH2 screwdrivers seamlessly. ...The design was adapted to perfectly fit the original Anet keyboard key, ensuring a secure and convenient storage solution.

I was experiencing issues with the Y-axis on my Anet, as the belt had become slightly loose in the unattached section. ...To resolve this problem, I designed a solution that has successfully tightened the belt.

... with a layer thickness of 0.2mm, wall thickness of 1.5mm, and an InFill Density of 25%. Although I'm not the most skilled designer or printer, I thought this modification might be helpful, so enjoy it and provide feedback if you like it – thanks!

The printable area of my new 3D printer is 400x400x350 mm. Heatbed (410X410X3mm): https://www.aliexpress.com/item/32904171739.html?spm=a2g0s.9042311.0.0.10f84c4d6jZKCX Removal Spring Steel (410x410mm):...

The printable area of my new 3d printer is 40x40x35 cm. Heatbed: https://www.aliexpress.com/item/32904171739.html?spm=a2g0s.9042311.0.0.10f84c4d6jZKCX Removal Spring Steel:...

This is my project for our standart 3D Printer with a fan 5010 which allows the printer to breath properly.I have been using it for more than six months and I'm very happy with it, because it sucks air from a higher place where the air is colder.

You need to attach a filament guide to the top-right corner of your 3D printer. ...This simple accessory helps keep the filament neatly aligned and prevents tangles or kinks during printing.

Edit it online https://www.tinkercad.com/things/8TA1o3oWQaPI purchased a Runout sensor on Aliexpress "3D Printer Filament Break Detection Module With 1M Cable Run-Out Sensor Material Runout Detector For Ender 3 CR10 3D Printer"Two wire connection to...

Mount a versatile tool holder directly to the A8's framework, specifically designed to accommodate screwdrivers, nippers, and precision tweezers. ...Securely attach this essential component to the right-hand side of the system unit above the power...

I changed to upgraded springs on my A8+. These were only 20mm in length which was roughly 4-5mm shorter than the standard springs. I designed these with a 2mm base so once in place your spring is back to its original length. ...I use a washer top &...

...... To assemble this, drill a 3mm hole in the A8 body. Make sure to double-check your work, ensuring the surface is level before drilling! This design was created with Tinkercad. ...You can edit it online at https://www.tinkercad.com/things/l7meQUx0TtX

I sought a way to attach my A8 firmly to a piece of wood. I discovered a design by "cd5656" but found it too small, with no grip on the threaded rods whatsoever. ... This setup is quite snug and was intentionally made 0.5mm shorter than necessary to...