anet a6 3d models

A couple of sketches were created, an authentic front panel and a revised one due to the thin edge near the rod mounts. ...The design was specifically tailored for the Y-Belt tensioner: https://www.thingiverse.com/thing:1959208 Be cautious with the...

Be extremely cautious - this device can shatter your front and rear plates at any moment. The front clamp is compatible with the following model: https://www.thingiverse.com/thing:1896013. The rear clamp, on the other hand, requires the specific...

Fast printing cable guide that keeps extruder and hot end cables out of z-axis rods' way. You may prefer this to a chain link guide if unsure or want something that prints extremely fast (under 20 minutes with Cura at 0.2mm). This design will...

<p>Simple and curvy (aerodynamically friendly) Is simple and it works way better than the original. ...The best result is achieved printing it with two perimeters and support (with the base rotated at 30º) 0.2 mm layer height.</p> Category: 3D Printer...

Support to be fixed on the corners of the printer for 30cm wide led bar 2.5cm.

We modify the 30mm fan to 40mm to increase airflow in the extruder.

i got tired of battling a screw driver and a wingnut on stripped out bed frame holes. ...uses a 3m locknut.

Modification of the original piece adding a final cap on the left side for the car's end stop.

This fix enhances the original design found at Thingiverse, specifically thing 2776244. The inspiration comes from things 2609797 and 2387420. ...A major issue with the standard model is that its components often failed to assemble properly or exhibited...

I had to secure the Z-axis motors with a sturdy attachment system that allowed for easy screwing to the base. I've redesigned the ejpsx project from scratch, resulting in a rock-solid Z axis motor mounting setup. ... Update 2018-04-15 23:00 I corrected...

I downloaded https://www.thingiverse.com/thing:2487759, but unfortunately, it came out a tad too small for my needs. The ends wouldn't wrap neatly around the frame, so I decided to extend it slightly. ...Despite this adjustment, one side still has 3mm...

I push out Smartfil Flex at a speed of 120 millimeters per second, rotating the axis by 240 degrees, with no heat bed.

Power meter enclosure designed to attach atop LCD housing found in another project: https://www.thingiverse.com/thing:2560566 This housing provides ample space to mount a 12V - 5V, 3A USB power supply unit for the Raspberry Pi Zero W installed...

I designed a simple brace to eliminate printer frame vibrations in the Y direction. Most frame braces don't provide enough support to fix the rear end of the printer to the base plate, but this one does. You can test it by rocking your printer back...

This is my very first 3D object, so be gentle with me. I made some tweaks to the original component for the 18mm proximity sensor: moved the ring a bit lower since otherwise you can't grip it firmly with the bolt; added a T-bar on the top fan ring to...

I used this spool holder for two years with great satisfaction: https://www.thingiverse.com/thing:2016985. However, after mounting a cable chain, I encountered serious interferences and had to relocate the spool holder. To resolve the issue, I...

https://youtu.be/imm5MkwVC6I https://youtu.be/_cuatKSBzWY https://youtu.be/FG3YZuvKhVk ---------------------------------------------------------------------------------------------------------------------- Индикатор высоты поднятия сопла над...

06/12/2017 V6. Updates are now live on MyMiniFactory! NEW UPDATES WILL BE AVAILABLE ONLY AT MYMINIFACTORY https://www.myminifactory.com/object/51483 Vent holes have been widened for improved airflow. 19/06/2017 V5. The printing angle has been...

Also required are six screws with a length of 20mm and a M3 thread size, each featuring a screw head diameter of 5.5mm. ...Additionally, four M3 nuts are needed, as well as two magnets with a diameter of 10mm and a thickness of 4mm.

I finally gave up fighting a stubborn screwdriver and a recalcitrant wingnut on a bed frame with stripped-out holes. ...Instead, I opted for a 3M Locknut that does the trick.

The design prevents the filament to get outside the guide.

I'm a YouTube video: https://www.youtube.com/watch?v=sx0xTL40XhU This 3D print features 20% infill and three-layer walls with supports. To prepare cuts and generate G-code, I rely on Inkscape along with the gcodeplot plugin from GitHub:...

The manufacturer fine-tuned the product by adjusting the top holes from 7.98mm to 8mm, eliminating the need for any additional drilling if it becomes overly snug. ...I'm impressed with the streamlined design, which also minimizes plastic waste.

This device was created using Tinkercad. ...Make changes to it instantly at https://www.tinkercad.com/things/08GFMtVqBW8

I recently utilized this connector: https://www.wekton.pl/59jr101-1frs-lr/p,222649 or something similar:...

Ras

Simple but very hard attached filament roll support. I used part of machine supplied, rod M8 and bolts. The supports are attached down by clips so no possibility to remove them by accident and distance is fixed with another part mounted after...

I'm glad we're on the same page, even if my English isn't perfect either. To avoid crashes like I had before, I needed a new plate that could withstand the impact. Here's what you'll need: * A glass plate measuring 220x260 mm (cut to size) * 2...