anafi tablet holder 3d models

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

There are also holes in the top for integrated cup/pen holders with a 3D-printed translucent sleeve and light strip channel so they light up too :-D I used birch butcher block. I tried some dark stains, but I found that the light birch did not take...

Sand as needed.I Also added a small dice holder that is able to hold 5x 12mm, 6 sided dice. This can be printed with no supports, and is just super glued into the container. See pictures for orientation.</p><p>&nbsp;</p><p>&nbsp;</p><p><strong>PRINT...

Don't do much larger than that.&nbsp;Assembly!There are some order specific details when it comes to assembly.Go ahead and add the m3 nuts for the belt holder screws first. Then screw in the bearing blocks. ...After that, you can put on whatever,...

Fan wire and 2pin jst plug has been accommodated for to keep wiring tidy. Find a local supplier of aquatic carbon filters and cut to suit holder. Holds 20mm thick filters.</p> <p>Please also note this lid enclosure is intended to fit my corexy...

Remove the paper from the other side, and firmly press the part against the interior wall of the plastic box in the marked locations, making sure that for the brackets, the U shaped rod holder is facing up, and for the passthroughs, that each is...

TL;DR first: Welcome to my Overhaul of the Creality Ender 2! Im starting here with version V2 (V1 is only in one picture; there was too much wrong with that), which comes in 2 iterations/stages: ++++++++ Stage 1: ++++++++ changing out the Heatbed to...

I used a smooth/wipeable melamine faced furniture board) 580mm x 450mm x 18mm, QTY 1A Spool of PETG ,QTY 1Some PLA ,QTY 1EiBotBoard, QTY 19V 1.5A AC/DC Power Supply Adapter 5.5mm x 2.1mmPen Holder, QTY 1Precision Hardened Steel Smooth Rods - 8mm,...

This allows for the using of the stepper shaft has the idler shaft has the initial version of the extruder. New filament coupler design to prevent miss-alignments. Included the stepper motor adapter sketchup file so you can modify/adapt the support...

The base parts are: Floor & Base parts: 1) Base (Base - Giant.STL) 2) Flat Base (FlatBase.STL & FlatBase - Center.STL) 3) Center Stage (CenterStage.STL) Street Light Parts: 1) Lamp Piece (Lamp.STL) 2) Lamp Pillar (LampPillar.STL) 3) Lamp Holder...

a clamp to add some tension to the bearing, or a holder for eyepieces or other accessories.MakingCut the aluminium tubes to size. The four legs need to be cut fairly accurately, there is some room for play but not much; try to get at least within...

Filament White - BQ Petg Red - Amazon Basics Petg Blue- Prima Select Sky Blue Petg Links to useful & cool accessories\Remix 1.Junction Box https://www.thingiverse.com/thing:4062301 2.Spacers\Helpers https://www.thingiverse.com/thing:4062291 3.Nut...

(if you want to go faster tune the speed up to 130%)All the stls are in the right orientation.The back plate can be laser cutted or 3d printed, all the files are included.Prints the following parts:1x PanelMeterClock_v1_Body: Prusament PETG, Preset...

(it is already in the settings in the .3mf files)Assembly:Print all three parts (hull, treads, and gun.)Superglue the treads to the hull.Place the gun on the roof.Superglue works best for gluing it together.It will scale easily if you want a larger...

It can hang off the plywood deck (¾ inch") or the slightly thinner shelving above.&nbsp;Support enforcers are neededNo gluingEasy to printDesigned on...

DXF and STEP files are available on the project documentation for all panels on all machine sizes In-Lid Spool Holder Our in-house spool holder was also designed with the V-Core 3 enclosure in mind. It can be securely installed inside the V-Core 3...

Glue is not needed on the outside of the Dupont holder. General: There are quite a few M3 inserts used in this project, and they should be heat set, but I glued them in on my kits. I decided to glue them in using clear Gorilla Glue since I have no...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

https://www.amazon.com/icepc-Channels-Cooling-Controller-Interface/dp/B08CXYZLBK The object on the upper rear crossbar is a holder for 1.5" PVC pipe. Print two of them and use 2 90 degree elbows and some pipe and make a spool holder. EDIT...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

It can be mounted anywhere, and the cables can be routed directly within the holder. I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). ...Il...

DXF and STEP files are available on the project documentation for all panels on all machine sizes In-Lid Spool Holder Our in-house spool holder was also designed with the V-Core 3 enclosure in mind. It can be securely installed inside the V-Core 3...

Take what's theirs and make it your own! ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1...

- https://www.printables.com/model/855331-megalopolis-dice-tower-with-a-story Electronics:Voltage Sensor Box - https://www.printables.com/model/784371-voltage-sensor-box Voltage Sensor Box - SMALL...

Avoid lifting and warped prints!Print all three parts (body, treads, roof option.)Superglue the treads to the body.Choose the roof option and glue, or leave it free and swap it out as needed!Superglue works best for gluing it together.It will scale...

If you have installed the latest firmware, you have the possibility to reverse the direction of rotation of the extruder without needing to touch the wires, go to the settings, keep the button pressed for 2 seconds, a new menu appears, click on...

At the end, insert the whole assembly in its position on the Central Support.Step 5: Glue the Pencils to the Upper Holder and Fix the Airfoil Blades NACA 0018The upper support has 4 cavities where 4 pencils should be stuck. To do this, you must place...

Rollbar03.stl - Rollbar with light holders. Servosaver01.STL - Basic servo saver for installing onto a servo arm or disc. Servosaver02.STL - Splined servo saver for installing onto a small servo spline. Servosaver03.STL - Splined servo saver for...

Did not add chains for X axis to reduce moving massUniversal Filament Drybox with Tush++Removed the spool holder from the printer to reduce vibrations. ...Built printer and filament shelves instead in the garageAsk in the comments if you are curious...