an alq 144 3d models

this is some load out to fit to the hard points for the 1/144 murasame. ...this includes Fuel drop pod ECM pod 3 engine pods (SR-71 ramjet style, FA style, square) 12" speaker pods in case you want to go macross update Gun pod GBU Cluster bombs

I spent years meticulously crafting a precise 1/144 scale model of a bunker, which can now be printed in its entirety as a single component. ...Alternatively, it can be segmented into distinct sections with minimal or no additional support structures...

This is a TS-MA2 Moebius from the show gundam seed. ...The grunt of gundam seed the TS-MA2 Moebius is prefect for getting shot down in droves when faced with something more dangers than a wet paper bag. This one is 1/144, yes they really are that big.

... by the Red Baron. ... 1/144 scale to match the scale used by the "Wings of Glory" game. The propeller is attached to the underside of the model, can be snipped off and fitted after printing. ... SLA/Resin printers are best for this small model.

... SWR of the antenna remains good throughout the 2m band. If you don't have access to a 3D printer or prefer not to spend time printing parts, you can purchase them online at http://hamshop.cz/anteny-c9/quadruple-oblong-na-144-mhz-plastove-dily-i305/.

Designed this re-pop hand stop for the Mossberg 144 LS series of rifles, since the originals always seem to be missing. Designed to use the factory hardware. Print as-is, with or without supports. ... Update: Adjusted the geometry of the back of...

Here is some heavy-duty equipment designed to fit onto the hard points of the 1/144 MuraSama. This gear includes fuel supply tanks, Electronic Counter Measures (ECM) pods and three engine modules, each with its own unique design: SR-71 style ramjet...

This is the flight booster for the 1/144 Sumo from Turn A Gundam. This is a WIP as it's being tested, will leave patch notes here if anything changes. Pre-supported files included, no instructions yet. edit, test done as of 19-04-2022 show that...

A simple base to protect the Nucleo-144 board from bent pins and desk scratches. Latest Version: f (December 2019) - a cutout is added for H745 and other ST-Link3 boards equipped with this feature. Previous Update: e (November 2019) - side cuts are...

Scaled it to 1-144 for battlegroup northag. You will need green Stuff, because the walls of the original are thin and at some areas there is a small gap between the filling and the wall. ...To print this could be very frustrating, but it worked somehow.

The diminutive yet formidable 1/144 scale model of the legendary British torpedo bomber, the Fairey Swordfish, sits proudly on display, its intricate details and rugged lines a testament to the ingenuity and skill of its designers. ...This tiny replica...

This is a 1/144 Connected Armoured Vehicle from Gundam seed, that ZAFT tank/AFV/AT gun. This file contains 36 parts, this includes 3 different turrets, MG, cannon, and linear gun, a 2nd rear hull part for disconnected use, instructions, and chitubox...

This is a what-if conversion for the 1/144 Daughtress to give it a prototype Satellite Cannon that was later used in the GX-9900 Gundam X. Think of it as a test bed to see if you could even fit such a weapon onto a mobile suit. part count 21 pre...

... over the top wing. 1/144 scale to match the scale used by the "Wings of Glory" game. The propeller is attached to the underside of the model, can be snipped off and fitted after printing. ... SLA/Resin printers are best for this small model.

Customized version of http://www.thingiverse.com/thing:1148986 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Instructions Using the following options: Letter spacing is 12 points at loop y position 0. Font...

Human Created Using Customized Version Of Https://Thingiverse.Com/Thing:536486Https://Www.Thingiverse.com/Apps/Customizer/Run?Thing_id=536486Https://Www.Thingiverse.com Instructions Using Following Options: Second_Letter N First_Letter A

solidworks

Customized version of https://www.thingiverse.com/thing:739573 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=739573

Customized version of https://www.thingiverse.com/thing:1333866 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1333866

Customized version of https://www.thingiverse.com/thing:408698 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=408698

Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901

Customized version of https://www.thingiverse.com/thing:753477 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=753477

Customized version of https://www.thingiverse.com/thing:3515810 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3515810

No description provided.