among us map model

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

 My model has had almost no use at this point but I don't think that PLA will be a problem in use, but consider PETG if you have it.HARDWAREUnfortunately we have limited hardware supplies where I live, so there is a strange mis-mash of sizes and...

Make sure to follow me to get a notification when it's uploaded!*** ###READ BEFORE PRINTING!### * First of all, this is a non-commercial print, this means you are not allowed to sell files or prints of this model. Not that I neccearily would have...

Specifically, the mouth utilizes inexact measurements, and inconsistencies in source models from the 3D printing process made it difficult to gain a good measurement. On the sketch, we measured the mouth to be 1.20cm from the side of the constraint...

Print the first layers in white and the following layers in another color. UseOnce printed, put a Tesa PowerStrip onto the base and stick it on a surface.Other modelsAlso have a look at all my customizable creations. There are more...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

  ENGLISH-------------Only tested on T12-X, but can work on equivalent models with boxes of the same dimensionsI found my T12-X soldering station a little too bulky, the screen not very visible and too dark. I also wanted to have all the...

You may need to adjust your printer, sand the chamber a little, or apply some force, as the parts were modeled to fit with ZERO clearance, to assure the best possible bond when using superglue. Just apply superglue to the syringe holder anywhere...

Filament Dry Box (Peli Case) Storetwo standard 200mm filament spools in an air-tight Peli Case. Perfecting for storing your hygroscopic filaments after drying. The Dry box can be configured to simply store the filament, or by drilling and tapping 4 x...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

And Happy Printing!-------------------------------------------------Originally designed in Fusion 360 and printed with Prusa Mini+ THIS MODEL IS UNDER CC (Creative Commons) LICENCE. Note: The DO NOT EAT sign might not print properly due to...

COMPATIBILITY ------------- This air assist fits the 20W "Vigotec VG-L7" laser, also sold as "KKmoon BX20" (2021 model). That's a diode laser with Ø15mm focus ring. The focus ring is 10mm high. ADJUSTABLE Z AXIS REQUIRED ...

But it works in the end ;)I hope this will help some people who own the same device !NB: You will need to adjust the slots in the 3d model according to the size of your battery contacts.&nbsp;2. Revision History</strong></h5><figure class="table"...

Verify the axle turns freely. Source File FreeCAD: BearingPegV4_2019.FCSTD Reinforced Within the pegs (excluding the original V4) 'pins' are embedded that promotes a strong cross pattern with lines at the stress point in addition to beveling....

(In the future, I'll model a printable screw-gun interface for people who can't get the part in question.) 4.#6-32 brass nut, 1/4" across (measured face to face), 3/32" thick (optional) McMaster-Carr 95130A120. Fits into a pocket on the gun carriage,...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 120-277V and 347V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring: These LED light...

If you want to use the hardware I intended this to use: Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge) Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I sliced it with Cura 4.4 so you can use per model settings to print the whole thing at once. I printed it at .15mm layer height.</p> <p>Here's a video of the toy with some details. ...The video has a lot of assembly photos at the end.<br/> <figure...

If you do this, make sure to account for the thickness of these things to ensure that everything ends up flush as it should be. I've included a Sketchup model with more information, like joint lines, as compared to the .stl files. ...I will post more...

Slice your model in your desired software and save your gcode 3. Place the created gcode in the same folder in which you extracted the exe 4. Double click to run the exe 5. Type the number of the option you wish to use, for the towers included in...

I have not modeled any nut traps in the parts because I think they will weaken them so all bolts here just screw into the plastic. I believe the parts are thick enough that the bolts will not loosen but time will tell._ 1. Completely disassemble...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

I based the design of these pieces off of the Ender 5+ model available on GrabCAD (https://grabcad.com/library/creality-ender-5-plus-1). There will eventually be a detailed pdf showing a build guide, confirmed material list, building and flashing...

The straps used to complete the clamp are downloadable from the original model's site https://www.prusaprinters.org/prints/122320-one-for-all-cable-strap-print-in-place-clamp&nbsp;How to create your clamp &amp; accessoriesSelect the clamp size...

Děkuji.Unfortunately, during this model, my 3D printer broke. So I didn't have time to print for the competition, but in the meantime I made everything on cardboard. I will deliver the side panels when I test them. Thank you.</p><p>CZ</p><p>Ve...

Works with the regular rectangular heat sinks or the Waveshare heat sink.Two different styles of ventilation openingsSTEP files available for easy remixingThis remix does not currently have an option to mount a fan inside the enclosurePowering the...

Z gap between support interface and model is 0.2 mm For the adapter plate I used standard supports with the same support options Other parts: For convenience, I included the 40 mm fan cap, part cooling duct and BLTouch mount from the original...

The Tunnelplan Wind Turbine is a 1:10 scale model of an existing wind turbine. The diameter of the rotor is 2000 mm (20 meters) and the tower height is 1200 mm (40 meters). the max.ceiling height inside the house. Solution 4 energy...