amiga 500 raspberry 3d models

No Amiga A500 was complete without a load of floppy disks scattered over the top ready to play.Therefor I designed a full-scale miniature floppy disk for the A500 Mini along with coloured blank disk labels.The Model is split up into two models for...

Workbench utilizes the Amiga's native windowing system called Intuition to provide the graphical user interface. Intuition manages the rendering of screens, windows, and gadgets (graphical elements, equivalent to widgets). Later versions of AmigaOS...

You could use glue to make it permanent, or increase the height of the disk a small amount before printing if you want to really jam it in there.  Floppy Disk Label(Right click and save, print 31.5mm x 16.6mm):  Update:Added a...

The ACA500plus case can be used with a Blizzard 1230 IV accelerator card, and it's also compatible with other accelerator cards. ...To ensure proper installation, please refer to the instructions provided.

Super simple remix of a nice raspberry pi 3 case. ...Just added an amiga logo as I'm using this rpi3 for a PiMiga system. The case I remixed: https://www.thingiverse.com/thing:1956623 The Amiga logo I added: https://www.thingiverse.com/thing:2374923

Amiga 500 Left Back Panel Remake with SD Card Slot - Non-Destructive. Consider Replicating the Entire Set Using Keystone Connectors. ...A Matching Right Rear Panel with Keystone Connectors and Arduino Leonardo Mount is also Available on Thingiverse at...

Bottom tray and button to fit a TEAC FD-235 PC floppy drive into an Amiga 500/500+. The bottom tray is secured to the drive with two screws on the side, and then the posts screw into the tray. A longer third screw i the dront of the drive is...

Amiga 500 cover expansion for a integration without a hole on your favorite older computer. This part cannot be used with an expansion like A500-HDD+, others. It's design to use a FPV connectors and ribbon, and a micro switch (6mmx6mmx9.5mm), or...

Amiga 500 cover expansion for a integration without a hole on your favorite older computer. This part cannot be used with an expansion like A500-HDD+, others. It's design to use a FPV connectors and ribbon, and a micro switch (6mmx6mmx9.5mm), or...

I really liked https://www.thingiverse.com/thing:3565598, but it wasn't perfect for my needs because I didn't need to include any extra equipment like an HD and wanted a case that was as small as possible while keeping the correct proportions. The...

This is a simple 2 piece stand for the A500 Mini. Print the 2 parts with 100% infill to make sure there's a little bit of weight to them. 0.2mm layer height works well, but pretty much any height should be fine for this. This was printed in...

This custom ejection button is specifically designed to match the unique A500 hole found on certain eject mechanisms and modified drive models, such as the Samsung SFD321B/LEB.

This is a simple 2 piece stand for the A500 Mini. Print the 2 parts with 100% infill to make sure there's a little bit of weight to them.0.2mm layer height works well, but pretty much any height should be fine for this.This was printed in Prusament...

I upgraded my outdated A500 power supply with a Meanwell RPT-60B and didn't want to make any visible holes in the case. So I created this bracket. For this, only one hole needs to be drilled inside, which won't be visible from the outside. Enjoy!

I reinforced the clip and installed additional ventilation to improve airflow.

The button I could find on the internet for the FB-354 (not FZ-354) was supposed to be glued in place according to an ebay ad I found for it.. Not good enough.. Not good enough at all..Totally reworked the model but let's call this a remix.Print with...

The AMIGAPI 1000 is an exact 3:1 scale model of the Amiga 1000, designed specifically for your Raspberry Pi. This model includes a 2.5" hard drive, SD extension, and 30 mm fan. You can also use it with just your Pi if you prefer. This case makes a...

Remix of https://www.thingiverse.com/thing:3565598, to accomodate a Raspberry Pi 4.

Remix of https://www.thingiverse.com/thing:3565598, to accomodate a Raspberry Pi 4.

Bill Of Materials:screw 20x2 2pcsscrew 15x2 2pcsscrew 10x2 2pcsscrew 12x3 4pcsfan cooler 40x40x10 (5 or 12V)

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

A mini floppy disk for your A500 Mini. I designed this to be printable and look great with a standard FDM printer using a standard 0.4mm nozzle(Prusa, Ender etc). But I've included a lot of detail(for such a simple model) that will really come out...

A new opening was carefully crafted, measuring 30mm in diameter, to seamlessly accommodate a HDMI cable and simplify future setup processes.

This is a remix. The Chinon drive needs to be moved back a bit to fit the lid. This projects makes brackets to move the disk back a bit. You will also need 2 x 25mm x 3 mm Wood Screws (back mounts) 1 x 6 mm x 3 mm Wood Screws (front mount) 5 x...

A Match Made in Heaven: Raspberry Pi 2 or 3 for Old-School Amiga Enthusiasts!

Customized version of https://www.thingiverse.com/thing:5579699 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5579699

Customized version of https://www.thingiverse.com/thing:5579699 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5579699

Customized version of https://www.thingiverse.com/thing:5579699 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5579699

This picture caught my attention and it was part of an article about the new Amiga 500. I caught fire and got very excited about this computer, thinking I could create my own 3D raytracings that I had seen on TV before. At Christmas I've got the...

When paired with the forthcoming Amibian emulation, which is still in development for the Raspberry Pi 4, it will form the foundation of a highly satisfying Amiga 1000 emulation experience. The front panel of the Amiga case has been thoughtfully...