ambition mods converter 3d models

Designed to convert the nose of the FlightLine 1.6m B-25J into the gunship version used extensively in the Pacific as a low level attack platform. Overview Remove the 'green house' nose canopy and replace it with a 3D printed nose shaped like...

 Replace the colored filament with clear PLA and finish the print.Material:  PLA (colored for the top layer, clear for the walls)Quality:  .12mmTemp:  200°CBed:   67°CPrint Speed:  50mm/s, first layer at...

The front cross member extrusion remains in place.</p> <p>I have designed this to work with my ender5plus corexy conversion that has all the steppers fitted within the stock dimensions. ...This will definitely not work with steppers hanging off the rear...

My pal Alan recently bought a small, newly converted, camper based on the Mazda Bongo minivan. In an amusing example of half-hearted badge engineering, some of these vans - Alan's included - were badged with "Ford" logos, front and rear, even though...

The model is saved and converted in STL files. There are 49 separate parts which you must print and assemble together. All the files have passed thorough checking and correction in Netfabb. The Atlas STL files can be easily handled in any slicing...

I spent a lot of time trying to clean up the body after converting it from the mesh. I used 3D builder to fix the non manifold errors but Prusa Slic3r says 2 remain. All the slicers I tried will still slice the model...

This project aims to convert a Bitcoin miner into a handy space heater. **We achieve this by:** * replacing all fans because we need the heater to be silent * enclosing everything because we dont want any wires exposed * replacing mining...

If you can source a 55x55cm bottom panel, good for you - these are not needed.5V XL4015 buck converter for powering the internalsArduino Nano for temperature control, sensors, fan control2x 120mm fans with PWM and RPM sensing (4 wires)2.4" LCD from...

It's very important to use a high quality thermocouple that is rated for 500 C for example, the stock Qidi thermocouple is only rated at 300 C.If you want to increase the print temp beyond 300 C (stock) you can enable it in firmware, I have commented...

Also get the remix for the inserts. 1x Martin's MMU Slot Buffer (SB) 5x SB PC4m10 inserts (a remix of the inserts to the SB buffer) These other mods are not listed here, and are also not discussed in the instructions at all,  but I feel help the MMU...

Basically you want to cut a single PCB trace (check with multimeter afterwards that the trace is cut)https://ardufocus.com/howto/28byj-48-bipolar-hw-mod/You can remove the end of the cable with the connector, we don't need it, as well as the red...

Do the mod at your own risk. Never leave your printer unattended, stock or not. Assembly Instructions Some pictures from the assembly guide below are from an earlier version of the carriage but the principle is the same for the assembly, the...

(Support Enforcers Only)Multiple Modules:Dual floor module - Space-Port-Residence-NW-R-V1 and Space-Port-Residence-NW-L-V1Standard module with connecting walkways - Space-Port-Residence-R-V1 and Space-Port-Residence-L-V1Additional walkway to bridge...

This is more of an Ender 3 design upgrade than an EnderLoop mod component, but I think it's worth mentioning, especially if you replace the default springs with stronger ones.I sadly managed to break endstops while I was tinkering with design and...

This Kit only works with the “on top of flipped brackets” pulley setup explained above, but is very minimal and creates not unsymmetric pulling force on the top of the leadscrews.&nbsp;Firmware Upgrades:I run all my printers with the Tiny Machines /...

Do the mod at your own risk. Never leave your printer unattended, stock or not. Assembly Instructions Some pictures from the assembly guide below are from an earlier version of the carriage but the principle is the same for the assembly, the...

Reef-Pi) * [2x Step-down Buck Converters](https://www.amazon.com/gp/product/B07CP4P5XJ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1) used to step down the 12V from the power supply to 3.3/5 volts for the raspberry-pi GPIO * [Reed...

In my case, there is an overheat issue with the extrusion stepper (it's hotter than other stock steppers), I think the new stepper has lower voltage than the stock one, I will add a buck converter to fix that. But it's not a design issue anyways. It...

Cam mechanisms are usually used to convert rotary motion into linear motion, but can be used for the inverse purpose just as well.Required3D Printer - accommodating a build size of at least 210x80mmFilament: no specific requirements I used mainly...

Tai sabaki is usually used to avoid an attack, such that the receiver of the attack ends up in an advantageous position and it is often wrongly referred to as "evasion." Takemusu Takemusu (武産) was the concept developed by Morihei Ueshiba of how the...

There is even a completely “new” type of generator/support/luggage coach converted from old mail coaches!Technical infoThe coaches had a wooden body construction with steel reinforcements in crucial spots and a chassis made out of steel. some earlier...

The figurine is modeled in Autodesk Maya and converted into STL file format. The files are checked and corrected in Netfabb to ensure a seamless 3D printing experience.The video game 3D model print parts are made solid, to facilitate their handling...

Wayne posted his drawing on his old website (archived at the Wayback internet archive) and it has also been posted on the Triumph Experience web forum on several occasions.Wayne's pdf's were converted to DXFs but were then heavily edited and errors...

Update V3: Ok so I didn't realize before I make an stl I should combine the parts into a single solid, then convert to stl. So some parts may print funky. Just fixed Battery tray, need to review other parts. Deleted old files, Should I do that? Going...

Every part is designed to fit on 18x19cm print bed and is converted into STL file format. The files can easily be handled in any slicing program, such as Cura 15.06 or Simplify3D.There are two scale versions for the 3D model:FFF/FDM 1.1 is scaled at...

USD 1.7) - plus a small AMS1117/LM1117 Step Down converter (approx. USD 0.2) - this one is for the Bluetooth module, which needs 5V</a> - The driver I use is a Visaton FRS 8 M - 8 Ohm 8 cm (3.3") full-range speaker (around USD 12). However,...

Select the black section, then invert selection to select everything in the image that is not the solid outline of the ship and delete/convert to transparent. This leaves just the solid blank outline of the ship and everything else transparent. ...

Since the unit is 12 volts I decided it would be fun (read mad scientist) to convert it to run off the EPS12V, or CPU, connector of a PC power supply. A quick PCB design later I had a simple 80x100 board that took the 8 pin, 336 watt, EPS12V...

Add another 10 mm for the perfect travel-height (without cutting).&nbsp;I'm intentionally not providing any specific offsets here since they heavily depend on the actual setup.Prepare the gcode for cuttingActually, any software can be used that...

*** Remix improvements, continued (plus some print/assembly notes):*** - To facilitate rotating the push block around (front to back) to easily switch between which thickness of side is facing your fence, the main handle provided has been redesigned...