ambico 57 inch tripod 3d models

Replacement for the little rubber camera holder on an ambico tripod.

Replacement tip for Ambico tripod that extends to 41". ... Approximate measurements Outside(mm): 24x17x12 Inside (mm): 22x12x7

... angle is around 61.5° and 45mm x 45mm square. * You might have to adjust your printer to find the right size for your tripod so the latch holds. * Printed with 50% infill due to the pressure of the latch. * The dovetail angel is 64°. ...

Tripod Mount for Ambico 40mm. ...The other models were too big on thingiverse to fit into my tripod.

Tripod Mount for Ambico 40mm. ...The other models were too big on to fit into my tripod.

SummaryTripod Mount for Ambico 40mm. ...The other models were too big on thingiverse to fit into my tripod.

For a fairly late model Ambico branded, all plastic quick release tripod, does not have a geared crank elevator. This tripod might not have been worth to rescue but it's lighter than my aluminum tripods, and the quick release block is kind of...

This is the knob that attaches to the rack & pinion height adjustment.

It fits tripods like Ambico, Velbon, and Amazon house brand, among others, with a 45mm/1-3/4 inches square dovetail design. More plates are needed, and an update reveals the base plate is too large for the PINHE4D pinhole camera without a spacer;...

This Ambico Model V-0552A tripod ended up in my closet, and of course the shoe was missing. So instead of looking around here I made a quick, quick release shoe for it in Fusion 360. The part that mounts at the widest point is 44mm then tapers down...

This is quick release mount pad for Polaroid 57 (PLTRI57) as seen below : "https://www.amazon.com/Polaroid-57-Inch-Carrying-Digital-Camcorders/dp/B004OVEJQC?th=1" This fits snugly in the tripod's quick release slot, which is supposed to be a QS-29...

Customized version of https://www.thingiverse.com/thing:2087895 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2087895

It's very easy to modify if you need to. The clamp goes from 57 to around 90mm. It's 40mm wide. It will hold thick phones, or a phone with a thick case. 15mm is around the limit. Depends on the shape.</li> <li>All parts are printed 100% solid.</li>...

Both seem to use the same tripod with 1.25" legs and a nearly useless tray. You know what I hate about telescope tripods? Barely any useful storage, that's what. I was complaining night and day and my wife finally told me to shut up and do something...

Mount for tripod (AmazonBasics 60-Inch Lightweight Tripod - https://www.amazon.com/gp/product/B005KP473Q). Holes for 1/4-20 and M3 screws. May need to scale in one direction ("Z") to get the fit more snug (UPDATE: I scaled "Y" by 1.13 (due to...

This is quick release mount for Polaroid 57 (PLTRI57) as seen below : "https://www.amazon.com/Polaroid-57-Inch-Carrying-Digital-Camcorders/dp/B004OVEJQC?th=1" This fits snugly in the tripod's quick release slot, which is supposed to be a QS-29 slot,...

... ...It's simply a printable nut for connecting the Pi camera tripod back to a tripod screw. @kevinlo's model requires a "real" nut, but I'd prefer to stick to plastic. :-) The nut is threaded correctly and should easily screw onto a tripod. ...

57

I used this to attach an art easel to an old tripod. ...I Had to shorten rricups alittle to get it to fit on the tripod mount " Quick Release Camera Mount for AMBICO / VELBON Tripod by schlem" top for adhesion purposes

... It mounts into a SLIK PRO 700DX tripod, allows you to mount half inch EMT ( electrical conduit ) and mount a ball on the end. This allows for mounting the phone mount on the end of the EMT. ...It is good for doing unboxing & desktop videos.

You can assemble your tripod and your gopro directly.

A phone holder for 3/8 inch tripod. It was made for my Samsung Galaxy Note 10+ but should fit other phones too. I've printed mine with PLA at 0,2 layer height. The most problematic part is thread because it has to be printed pretty precise. BOM:...

A phone holder for 3/8 inch tripod. It was made for my Samsung Galaxy Note 10+ but should fit other phones too. I've printed mine with PLA at 0,2 layer height. The most problematic part is thread because it has to be printed pretty precise. ...

Mounting plate with a 5/8" thread for the Bosch Professional tripod 0601096B00 .For mounting 5/8" inch laser level and other equipment.&nbsp;I recommend printing with 25% Infill and at least 4 Perimeters, supports neededI added holes for m3 nut and...

tripods are sold with only one quickrelease.... so i designed one for my second (small) camera... al the parts are 3d printed.... this is version 2, version one had several issues. The only remark is that you have to put some non slippery surface...

( I bought mine here: https://armysurpluswarehouse.com/camo-netting-poles-fiberglass-4-for-11-95/ ) Many ham/amateur radio operators use these poles to create antenna masts, and this tripod can help with stability and set up. UPDATE: I've included a...

remote holder EQ mount for 1.7 inch tripod

1x M8 Bolt and Nut 1x AmazonBasics 60-Inch Lightweight Tripod

Hey, this is adapter from tripod head 16mm to 1/4 inch. Thanks to this, you can mount a camera, camera, microphone or lamp on a small and cheap lighting stand. ... Additionally you need: 3x M5 screws und nuts Adapter 1/4 tp 3/8 inch Reduction from...

This device will clamp onto your Ioptron tripod and hold your mount controller. Tested with the controller for a CEM60. Requires 4 screws & nuts. ...I used #6-32 X 1/2 inch.